Datex-Ohmeda S/5 B-GAS Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 83

background image

Datex-Ohmeda S/5 Anesthesia Monitor

Document No. 800 1005-1

42

3.4

Adjustments and calibrations

See

User’s Reference Manual

for normal gas calibration instructions.

3.4.1

Gas sampling system adjustment

Flow rates should be measured and possibly adjusted under the following conditions:

•

After any part within the sampling system has been replaced

•

Gas response is slow

NOTE: Adjust the flows with a new, clean D-fend water trap and original Datex-Ohmeda sampling

line.
NOTE: Before adjusting the flows, make sure that there is no leakage in the sampling system.
NOTE: Let the monitor warm up for 30 minutes before measuring flow rates.
For the flow rate measurements a flowmeter with a low flow resistance and capability to measure

low flow rates is required. A normal length of sampling line has to be connected to the monitor as it

has a considerable effect on the flow.
The flow rates are adjusted by changing the flow resistance cassettes (constriction cassettes) in the

sampling system. See Table 2 in chapter “

Gas sampling system”

for the alternative cassettes.

The adjustments and the respective constrictions to be adjusted are shown in the next figure, see

also chapter

“Gas sampling system”

to see gas sampling system block diagrams for modules

manufactured since autumn 1998.

3.4.2

Flow rate measurement

If any flow rates are not correct, first replace the D-fend water trap. Then recheck the

incorrect flows before adjusting the flow rates.

The sampling flow rate is measured by a flowmeter at the sampling line. The rate should be

between 180 and 220 ml/min.
The sampling flow rate is adjusted by changing the flow cassette which is located between the

pump and the damping chamber.
Due to two different tubing layouts, if the described location does not contain a flow cassette, the

sampling flow rate is adjusted by changing the flow cassette that is located between the pump and

the sample gas out connector.

«
...
46
47
48
49
50
...
»

Содержание S/5 B-GAS




















































































Отзывы:

Нет отзывов

Похожие инструкции для S/5 B-GAS

Бренд: Garmin Страницы: 12

Бренд: U-Prox Страницы: 31

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: NEC Страницы: 146

Бренд: Manfrotto Страницы: 16

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 128

VLT DriveMotor FCP 106

Бренд: Danfoss Страницы: 4

Бренд: Zeagle Страницы: 37

Бренд: Jands Страницы: 7

coviva Smartbox TKP100A

Бренд: hager Страницы: 34

Бренд: Lawler Страницы: 5

Бренд: VAT Страницы: 39

Бренд: Samson Страницы: 124

Бренд: Samson Страницы: 86

Бренд: VAC Страницы: 5

Бренд: UNICORECOMM Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды