Dataradio Integra-TR Скачать руководство пользователя

Страница: 59 / 68

5-2

Part No. 001-4008-101/102

Table 5-2 Normal Factory Settings (Bases)

Refer to help files for descriptions of the above fields.

Fields

Full Duplex Base Integra-TR with
other Integra-TR

Redundant Integra-TR Full Duplex
Base with Integra-TR/ Integra-T

RX Unit

TX Unit

Rx Units

TX Units

Network Settings

Compatibility Mode

Integra-TR

Integra-TR and Integra-T

Tx/Rx Mode

Rx Only

Tx Only

Rx Only

Tx Only

Extended Preamble (ms)

Network Speed

19200 Full Channel, 9600 Half Channel,

or 2400 Quarter Channel

9600 Full Channel

Tx Time Out

Disable

Tx Online Diagnostics

Yes

Unit Type

Master

Data Delivery

All

Suspend Period (ms)

Activity Time-out (sec)

Sleep Mode

Disable (N/A)

COM Port

Device Baud

19200

9600

Data fwd timer

Normal

Parity

8 bit, no parity, 1 stop bit

Break

Ignore break

Xmit Control

DOX

Active

DCD Control

Analog Connector

Analog 1

Input

Fan Control

Input

Fan Control

Analog 2

RxTp

Input

RxTp

Ant. SW Control

Frequency

Transmit

User Choice

Receive

User Choice

Adjustments

Carrier Sense (-dBm)

105

(N/A)

110

(N/A)

Power Out

255 (indicates 5 Watts nominal)

Frequency Warp

Grayed out (radio dependant) Values are set at factory; can be changed if required; hit

release test button to enable field

Deviation

Содержание Integra-TR





































































Результаты поиска

Содержание Integra-TR

Отзывы:

Похожие инструкции для Integra-TR

Бренды по названию

Популярные бренды

Dataradio Integra-TR, Техническое руководство

Результаты поиска

Содержание Integra-TR

Отзывы:

Похожие инструкции для Integra-TR

Бренды по названию

Популярные бренды