Dataradio Integra-TR Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 68

Dataradio Integra-TR Скачать руководство пользователя страница 46

2-26

Part No. 001-4008-101/102

Temperature

Internal temperature (in degrees Celsius)

Forward Power

Forward power (in watts)

Reverse Power

Reverse power (in watts)

Analog Input 1

Voltage on the External Analog 1 Input from the Power / Analog Connector (in volts)

Analog Input 2

Voltage on the External Analog 2 Input from the Power / Analog Connector (in volts)

Preamble Good

The number of correctly decoded transmissions received in the last 15. Used with Preamble Total, this
serves as an indication of how well the unit is receiving data.

Preamble Total

The number of total transmissions detected, maximum is 15. Used with Preamble Good, this serves as an
indication of how well the unit is receiving data.

RSSI /Pwr

This panel shows the current RSSI level (in dBm) while the local unit is receiving and the current power
level (in watts) while the local unit is transmitting.

Rev Pwr

This check box changes forward power to reverse power on the Power Panel from while the local unit is
transmitting.

Tx Mode

This box allows the user to select different transmit modes when the unit is told to transmit.

z

Tone - the unit transmits a 1200 Hz tone

z

Mod Balance - the unit transmits a 100 square wave

z

Random Data - the unit transmits random data

z

No Modulation - the unit transmits with no modulation

«
...
44
45
46
47
48
...
»

Содержание Integra-TR





































































Отзывы:

Нет отзывов