Dataradio Integra-TR Скачать руководство пользователя страница 57

Страница: 57 / 68

4-5

Part No. 001-4008-101/102

Table 4-3 Typical Transmit Deviation

Connected to an Integra-TR, Full Channel, Part Number 242-40X8-Y30, Native Compatibility Mode

Network Speed
(in b/s)

Typical Deviation
(kHz)

Voltage at Pin 4 when receiving that deviation from other
units (white wire of analog/power connector) (Vpp)

19200 + 4.0

1.5

9600

+ 4.0

1.5

4800

+ 4.0

1.5

Connected to an Integra-TR,

uarter Channel, Part Number 242-40X8-XXX, Native

Compatibility Mode

Connected to an Integra-TR, Half Channel, Part Number 242-40X8-Y10, Native Compatibility
Mode

9600

+ 2.5

1.5

4800

+ 2.5

1.5

Connected to an Integra-TR, Full Channel, Part Number 242-40X8-Y30, Integra-T/Integra-TR
Compatibility Mode

9600

+ 3.0

1.5

4800

+ 3.0

1.5

Connected to an Integra-TR,

uarter Channel, Part Number 242-40X8-XXX, Native

Compatibility Mode

4800

+ .05

1.5

2400

+ 1.64

1.5

Connected to an Integra-T, Full Channel, Part Number 242-40X7-Y30

9600

+ 3.0

1.5

4800

+ 4.0

1.5

Содержание Integra-TR





































































Результаты поиска

Содержание Integra-TR

Отзывы:

Dataradio Integra-TR, Техническое руководство, Страница: 57 / 68

Результаты поиска

Содержание Integra-TR

Отзывы: