manualshive.com logo in svg

Dataradio Integra-TR, Техническое руководство, Страница: 14 / 68

Поделиться
Скачать
Dataradio Integra-TR Скачать руководство пользователя страница 14

1-12

Part No. 001-4008-101/102

1.9 FIRMWARE UPGRADES

The Integra-TR firmware resides in flash EPROM and is designed to allow field upgrades.

Upgrades are done using a PC connected to the Integra-TR but do not require opening the unit. Upgrades 
require intervention with DRL’s Technical Service.

1.10 NETWORK APPLICATION

Integra-TR is suited to a variety of network applications. Its primary design goal was to satisfy the needs of 
SCADA systems using RTUs or PLCs in either point-to-point or point-to-multipoint service.

This section gives an overview of some common configurations. Selection of “master” or “remote” as well 
as data delivery conditions is done using the Integra-TR Field Programming Software.

1.10.1  RF PATH AND COMMUNICATIONS RANGE

Integra-TR is designed for use over distances up to 30 miles (50 km) depending on terrain and antenna 
system. To assure reliable communications, the RF (radio frequency) path between stations should be 
studied by a competent professional who can determine what antennas are required and whether or not a 
repeater is needed.

1.10.2  BASIC CONNECTIONS

The connections required are shown in Figure 1-3. 

While an RTU or PLC is shown in the diagram, master 
stations often use a PC running an application designed to 
communicate with remote RTUs or PLCs. The Setup PC is 
used for both configuration and local  and remote 
diagnostics. It may be left connected at all times but is not 
required for normal operation once the unit has been 
configured.

Integra

®

Antenna

Integra 

Setup PC

RTU or PLC

13.3VDC / 3A 
Regulated power supply
connects on rear

Содержание Integra-TR





































































Отзывы:

Нет отзывов