Dataradio Integra-TR Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 68

Dataradio Integra-TR Скачать руководство пользователя страница 25

2-5

Part No. 001-4008-101/102

Figure 2-6 Integra-TR Field Programming Software Startup Screen

2.4 INTEGRA-TR FIELD PROGRAMMING SOFTWARE

2.4.1 Introduction

The Integra-TR Field Programming Software is the programming and diagnostics software for the Dataradio
Integra-TR wireless modem. The Field Programming Software allows the user to edit and program user
programmable settings, interactively tune modem and RF parameters, and monitor diagnostic data from the
Integra-TR. See Figure 2-6 for the Integra-TR Field Programming Software startup screen.

This manual assumes the Field Programming Software has been installed on the user’s PC with at least one
operational serial COM Port available.

2.4.2 COM Port Settings

Integra-TR programming is done through the PC’s Primary COM Port. Primary and secondary COM ports
are configured with the Field Programming Software. The programming cable (included in the
Programming Kit - DRL part number 250-4008-001) is connected from the Setup Port on the Integra-TR to
the PC’s COM port configured as the Primary Port. The Port Settings screen of the Field Programming
Software is accessed via the Utilities pull-down menu (see Figure 2-7). The Port Settings screens are used to
configure the PC’s serial COM Ports. COM Port parameters are defined in 2.4.2.1. COM Port assignments
are displayed in the bottom status bar of the Integra-TR Field Programming Software screen.

2.4.2.1 COM Port Parameters

COM Port

Selects COM Port number (COM 1-4) for Primary and Secondary COM Ports (see Figure 2-7).

«
...
23
24
25
26
27
...
»

Содержание Integra-TR





































































Отзывы:

Нет отзывов