Datakom DKG-507 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 54

background image

DKG-507 User Manual V-42

(24.05.2013)

- 24 -

The unit offers 2 sets of voltage and frequency protection limit values. The user is allowed to

switch between these 2 sets anytime.

This feature is especially usefull in dual voltage or frequency gensets for easy switching

between 2 operating conditions.

The switching to the second set of limit values is performed by applying signal to the SPARE-1

digital input.

In order to assign this functionality to the SPARE-1 input, the program parameter

P_092

Secondary Volt/Freq

should be set to 1.

Below parameters are available for second voltage-frequency selection:

Mains Low Voltage Limit
Mains High Voltage Limit
Mains Low Frequency Limit
Mains High Frequency Limit

Genset Low Voltage Shutdown Limit
Genset Low Voltage Warning Limit
Genset High Voltage Warning Limit
Genset High Voltage Shutdown Limit
Genset Low Frequency Shutdown Limit
Genset Low Frequency Warning Limit
Genset High Frequency Warning Limit
Genset High Frequency Shutdown Limit
Genset Low RPM Shutdown Limit
Genset Low RPM Warning Limit
Genset High RPM Warning Limit
Genset High RPM Shutdown Limit

If the unit is used in a single phase electrical network, it is advised t set the

Single Phase

Enable

program parameter in

CONTROLLER CONFIGURATION

group to 1.

When

Single Phase Enable

is set to 1, then the unit will measure electrical parameters only

on phases

L1

of genset and mains.

Voltage and overcurrent checks will be performed on phases

L1

only.

Phases

L2

and

L3

parameters, as well as phase-to-phase voltages are removed from display

screens.

The unit is capable to be programmed to ask for a password when AUTO or RUN mode is

selected.

The password is adjusted with parameter P_115. If the password is set to zero, then the unit

will not ask for password.

When the unit asks for password, enter the password with

▼

and

▲

buttons, then

acknowledge with

MENU

button.

6.27. Password Operation (applicable only to DKG-517CAN/MPU)

6.26. Single Phase Operation

6.25. Dual Voltage and Frequency

«
...
22
23
24
25
26
...
»

Содержание DKG-507























































Отзывы:

Нет отзывов

Похожие инструкции для DKG-507

Бренд: Vacon Страницы: 64

RDS17S-ELITE1-R1

Бренд: D&R ELECTRONICS Страницы: 12

iDual A E27 iD60

Бренд: jedi LIGHTING Страницы: 23

Бренд: Linak Страницы: 33

LMT070DICFWD-NJN

Бренд: Topway Страницы: 34

Бренд: Fluidmaster Страницы: 2

Бренд: M-system Страницы: 7

Бренд: D+H Страницы: 12

Бренд: DUCH Страницы: 9

Бренд: EFI Страницы: 55

Бренд: Dantherm Страницы: 36

DIGI-STAR GT400

Бренд: AGRI TRONIX Страницы: 26

DAQP-CHARGE-B Series

Бренд: Dewetron Страницы: 14

PHAZR-5 UR5U-9000

Бренд: Universal Remote Control Страницы: 2

Бренд: Universal Remote Control Страницы: 5

by-me Eikon 20521

Бренд: Vimar Страницы: 6

Бренд: CLA-VAL Страницы: 43

Бренд: One for All Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды