Datakom DKG-507 Скачать руководство пользователя страница 21

Страница: 21 / 54

DKG-507 User Manual V-42

(24.05.2013)

- 21 -

The unit offers automatic exerciser operation. The exercise operation may be done on a daily,

weekly or monthly basis.

The start day and time of the exercise is programmable as well as its duration. The exercise

may be done with or without load following programming.

Program parameters related to the exerciser are:

Exercise start day and hour

Exercise duration

Exercise off_load/on_load

Exerciser Period (Daily / Weekly / Monthly)

Please refer to the programming section for a more detailed description of the above

parameters.

When the start day and hour of exercise has come, the unit will automatically switch to either

OFF_LOAD TEST

LOAD TEST

mode. The engine will run and if the on_load exercise is selected

then the load will be transferred to the genset.

If a mains failure occurs during the off-load exercise, the load will not be transferred to the

genset unless the

Emergency Backup Operation

is allowed by setting the related program

parameter to 1. Thus it is highly recommended that the Emergency Backup mode enabled with off-
load exerciser.

At the end of the exercise duration, the unit will switch back to the initial mode of operation.

If any of the mode selection keys are pressed during exercise, then the exercise will be

terminated.

Using the daily exercise mode, the unit may feed the load from the genset during predefined

hours of the day. This operation may be used in high tariff periods of the day.

In order to resume to the factory set parameter values:

-hold pressed the

OFF, LAMP TEST

and

ALARM MUTE

buttons for 5 seconds,

“

FACT RSET

” will be displayed

-immediately press and hold pressed the

ALARM MUTE

button for 5 seconds

-factory set values will be reprogrammed to the parameter memory and

“

FACT RSET DONE

”

will be displayed during 5 seconds.

It is not possible to restore user parameters.

6.18. Resuming to factory set parameters

6.17 Exerciser

Содержание DKG-507























































Результаты поиска

Содержание DKG-507

Отзывы:

Похожие инструкции для DKG-507

Бренды по названию

Популярные бренды

Datakom DKG-507, Руководство пользователя

Результаты поиска

Содержание DKG-507

Отзывы:

Похожие инструкции для DKG-507

Бренды по названию

Популярные бренды