Datakom DKG-507 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 54

background image

DKG-507 User Manual V-42

(24.05.2013)

- 15 -

The Delayed Mains Simulation feature is used in battery backed up telecom systems where

batteries are able to supply the load during a certain period. The genset is requested to run only when
battery voltage drops below the critical level. Once the engine runs, the rectifier system starts charging
the batteries and the battery voltage goes up immediately. Thus the engine should continue to run a
programmed period for effective charging. The critical battery voltage level will be detected by an
external unit which provides the digital Simulate Mains signal for the genset control unit.

The unit offers an optional

SIMULATE MAINS

signal input. The

SPARE-2

digital input may be

assigned as

Simulate Mains

using program parameter

P_084.

It is also necessary to set the

ACTION

program parameter of the related input to

3

in order to

prevent any alarms generated from this input.

The SIMULATE MAINS signal may be a NO or NC contact, switching to either battery positive or

battery negative. These selections are made using the programming menu.

If the

Delayed Simulate Mains

program parameter (

P_085

) is set to 1 and the input signal is

active when the genset is not feeding the load, the mains phases are not monitored and supposed to
be inside limits. This will prevent the genset from starting when the simulate mains signal is present
(batteries charged). The genset will start when mains voltages are out of limits and the simulate mains
signal not present.

If the genset is running when the signal is applied, then MAINS SIMULATION will be

prevented during

P_086

Flashing Relay Timer

program parameter. After this, usual Mains Waiting

and Cooldown cycles will be performed before engine stop. When the SIMULATE MAINS signal is
present, the front panels mimic diagram’s mains LEDs will reflect the mains voltages as present.

When the signal is passive, the unit will revert to normal operation and monitor the mains

voltage status.

The REMOTE START operation overrides DELAYED
SIMULATE MAINS operation. When both parameters
“Remote Start Operation” and “Delayed Simulate
Mains” are set then REMOTE START operation mode is
performed.

6.8 Delayed Mains Simulation, Battery Charging

«
...
13
14
15
16
17
...
»

Содержание DKG-507























































Отзывы:

Нет отзывов

Похожие инструкции для DKG-507

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: ABB Страницы: 139

Бренд: ABB Страницы: 28

Бренд: ABB Страницы: 59

Бренд: S&C Страницы: 40

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: 7bit Страницы: 2

Бренд: Jafar Страницы: 15

Бренд: Manfrotto Страницы: 16

Бренд: Fanimation Страницы: 2

Бренд: M2M Страницы: 24

Бренд: HandyTrac Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды