Datakom DKG-507 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 54

background image

DKG-507 User Manual V-42

(24.05.2013)

- 19 -

The GSM SMS sending is activated by setting the

SMS Enable

program parameter to

1

.

When a fault condition occurs, the unit will compose an SMS message and will send it to up to 6

phone numbers. If modem is enabled, only 4 telephone numbers are available for SMS sending.

The unit is also able to send SMS messages in below conditions, without creating a visible alarm

or warning:

Mains Fail, Mains Restored

(enabled via

SMS on Mains Change

program parameter)

Fuel Theft, Fuelling

(enabled by setting the

Fuel Consumption / Hour

parameter to other than 0)

If both modem and SMS are enabled, the unit will send SMS messages first and attempt modem

connection afterwards.

The maximum number of alarms transmitted in a SMS message is 4. This limitation is due to the

maximum length of an SMS message which is 160 characters.

A sample GSM SMS message is given below:

DKGxxx <SITE-ID>
STOP :LOW OIL PRESSURE SW.
END OF ALARM LIST

The first line of the message carries information about the unit type and the site identity string.

This line is intended for the identification of the genset sending the SMS message.

Each following line will give one fault information. The message will always be terminated by the

“

END OF ALARM LIST

” string.

When the message is sent, the existing alarms will be masked, causing the audible alarm relay to

release and preventing consecutive GSM SMS messages. Any new upcoming alarm will result in a new
GSM SMS message. The new message will indicate all existing alarms, even masked ones.

The necessary GSM modem cable will be supplied by DATAKOM. This is the same cable as

PSTN (land) modems.

If

Modem Enable

or

SMS Enable

or

MODBUS Address

parameters are different from zero, the local PC
connection will not work.

6.15 SMS Message Sending

«
...
17
18
19
20
21
...
»

Содержание DKG-507























































Отзывы:

Нет отзывов

Похожие инструкции для DKG-507

Бренд: Waters Страницы: 55

Бренд: Paradox Страницы: 2

Бренд: J3C Страницы: 2

Бренд: National Instruments Страницы: 29

Бренд: Samson Страницы: 73

Бренд: V2 Страницы: 48

Бренд: Aulisa Страницы: 32

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 26

Бренд: Reliance Foundry Страницы: 3

Бренд: Wesa Страницы: 8

Бренд: Gemini Страницы: 9

Бренд: M-system Страницы: 18

Бренд: WABCO Страницы: 3

MultiConnect Dragonfly MTQ-MNA1-B01

Бренд: Multitech Страницы: 45

Бренд: Bardiani Страницы: 22

Бренд: Danfoss Страницы: 10

Бренд: SimCom Страницы: 13

Бренд: Waeco Страницы: 168

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды