Datakom DKG-507 Скачать руководство пользователя страница 47

Страница: 47 / 54

DKG-507 User Manual V-42

(24.05.2013)

- 47 -

The parameters below define the functions of relay outputs. The unit has 6 relay outputs. The

fixed function relays are Fuel, Start, Mains Contactor and Generator Contactor. RELAY-1 and RELAY-
2 have programmable functions, selected from a list.

The relays may be extended up to 22 using

Relay Extension Modules

.. Other relays are in

the optional Extension Modules.

Program Group: Relay Definitions (password level-2)

PGM Parameter Definition Unit Fac.Set Description

P_226

Relay 01 Definition

RELAY-1 function selected from list

P_227

Relay 02 Definition

RELAY-2 function selected from list

P_228

Relay 03 Definition

RELAY-3 function (expansion module) selected from
list

P_229

Relay 04 Definition

RELAY-4 function (expansion module-1) selected
from list

P_230

Relay 05 Definition

RELAY-5 function (expansion module-1) selected
from list

P_231

Relay 06 Definition

RELAY-6 function (expansion module-1) selected
from list

P_232

Relay 07 Definition

RELAY-7 function (expansion module-1) selected
from list

P_233

Relay 08 Definition

RELAY-8 function (expansion module-1) selected
from list

P_234

Relay 09 Definition

RELAY-9 function (expansion module-1) selected
from list

P_235

Relay 10 Definition

RELAY-10 function (expansion module-1) selected
from list

P_236

Relay 11 Definition

RELAY-11 function (expansion module-2) selected
from list

P_237

Relay 12 Definition

RELAY-12 function (expansion module-2) selected
from list

P_238

Relay 13 Definition

RELAY-13 function (expansion module-2) selected
from list

P_239

Relay 14 Definition

RELAY-14 function (expansion module-2) selected
from list

P_240

Relay 15 Definition

RELAY-15 function (expansion module-2) selected
from list

P_241

Relay 16 Definition

RELAY-16 function (expansion module-2) selected
from list

P_242

Relay 17 Definition

RELAY-17 function (expansion module-2) selected
from list

P_243

Relay 18 Definition

RELAY-18 function (expansion module-2) selected
from list

Содержание DKG-507























































Результаты поиска

Содержание DKG-507

Отзывы:

Похожие инструкции для DKG-507

Бренды по названию

Популярные бренды

Datakom DKG-507, Руководство пользователя

Результаты поиска

Содержание DKG-507

Отзывы:

Похожие инструкции для DKG-507

Бренды по названию

Популярные бренды