Datakom DKG-507 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 54

background image

DKG-507 User Manual V-42

(24.05.2013)

- 23 -

The unit offers possibility of updating the firmware in the field. The firmware is updated through

the RS-232 serial port using Rainbow or a special DOS program.

The unit will go to firmware download mode with a special command from the PC program. In

download mode, the display of the unit will show “

DL V1.00

”

During firmware update process, the progress is visible through a percentage counter on the

screen.

The firmware update operation will take around 3 minutes.

After completion of the update a special command will set back the unit to normal operation

mode.

Volvo engines equipped with

EMS-II

engine control unit have the engine speed selectable

through the J1939

– CANBUS. The unit offers the possibility to the user to switch between the primary

and secondary speed using the programming menu.

If the program parameter

Volvo Speed Toggle

is increased, the unit will freeze for a few

seconds and switch the engine to 1800 rpm, which is generally the secondary speed. When the
parameter is decreased, the speed is set to the primary speed, which is generally 1500 rpm.

Please note also that a fine adjustment of the engine speed in the ± 8 % range may be done

using the program parameter

J1939 Speed Adjust

.

In engine control mode, the unit is supposed to control an engine without alternator.

The engine control mode is activated by a program parameter in the

Controller

Configuration

group.

When the

Engine Control Mode

is activated:

-the unit will not display genset AC parameters (volts, amps, kW and pf).
-genset voltage and frequency protections are disabled. However engine rpm protections will
be active.

It is strongly recommended to enter correct low and
high rpm limit values in order to enable engine speed
protection.

Daha önceki parametre değerlerine geri dönüş
mümkün değildir.

The unit must be in OFF mode, otherwise the speed
switching will not be performed.

Daha önceki parametre değerlerine geri dönüş
mümkün değildir.

6.24. Engine Control Mode

6.23. Changing the Default Engine Speed in Volvo Engines

6.22. Firmware Update

«
...
21
22
23
24
25
...
»

Содержание DKG-507























































Отзывы:

Нет отзывов

Похожие инструкции для DKG-507

Бренд: Ubisys Страницы: 2

Concord express

Бренд: GE Страницы: 3

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: dbx Страницы: 52

Бренд: Hankscraft Runxin Страницы: 58

Gemini GEM-P9600

Бренд: NAPCO Страницы: 6

Gemini GEM-P816

Бренд: NAPCO Страницы: 56

Бренд: Parkside Страницы: 86

Бренд: Vacon Страницы: 132

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 426

Бренд: YASKAWA Страницы: 26

Бренд: YASKAWA Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды