Datakom DKG-507 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 54

background image

DKG-507 User Manual V-42

(24.05.2013)

- 36 -

PGM

Parameter Definition

Unit

Fact.Set Description

P_043

Genset Contactor
Timer

sec

1

This is the period after the mains contactor has
been deactivated and before the generator
contactor has been activated.

P_044

Mains Contactor
Timer

sec

1

This is the period after the generator contactor has
been deactivated and before the mains contactor
has been activated.

P_045

Stop Solenoid Timer

sec

10

This is the maximum time duration for the engine
to stop. During this period the STOP relay output
is energized (if assigned by

Relay Definitions

). If

the genset has not stopped after this period, a

FAIL TO STOP

warning occurs.

P_046

Number of Starts

-

3

This is the maximum number of start attempts.

P_047

Mains Phase Order
Enable

-

0

0:

mains phase order checking disabled

1:

if mains phase order is faulty, then a warning is

given and mains contactor deenergized.

P_048

Genset Phase Order
Loaddump

-

0

0:

genset phase order checking disabled

1:

if genset phase order is faulty, then a loaddump

is generated and the genset stops after cooldown.

P_049

RPM from genset
frequency

-

1

This parameter is used in the conversion of the
genset frequency to engine rpm.
0: read rpm from the optional MPU input
1: convert frequency to rpm (using crank teeth
count)

P_050

Crank Teeth Count

-

30

This is the number of pulses generated by the
magnetic pickup sensing unit in one turn of the
flywheel.
This parameter is also used in the conversion of
the genset frequency to engine rpm. The
frequency in Hz is multiplied with this parameter
during conversion to rpm.

P_051

Low rpm Shutdown

rpm

0

If the engine speed goes under this limit, a

GENSET

LOW SPEED

alarm is generated and the engine

stops.

P_052

Low rpm Warning

rpm

0

If the engine speed goes under this limit, a

GENSET

LOW SPEED

warning is generated.

P_053

High rpm Warning

rpm

0

If the engine speed goes over this limit, a

GENSET

HIGH SPEED

warning is generated.

P_054

High rpm Shutdown

rpm

0

If the engine speed goes over this limit, a

GENSET

HIGH SPEED

alarm is generated and the engine

stops.

P_055

Alarm Relay Timer

sec

60

This is the period during which the

ALARM

relay

is active. If the period is set to 0, this will mean
that the period is unlimited.

P_056

Intermittent Alarm
Relay

-

0

0:

continuous

1:

intermittent (turns on and off every second)

P_057

Service Engine Hours

hour

50

The

SERVICE REQUEST

led indicator will turn on

after this quantity of engine hours from the last
service. If the period is set to ‘0’ no

SERVICE

REQUEST

will be generated depending on engine

hours.

P_058

Service Period

month

6

The

SERVICE REQUEST

led indicator will turn on

after this amount of time from the last service. If
the period is set to ‘0’ no

SERVICE REQUEST

will

be indicated depending on time.

«
...
34
35
36
37
38
...
»

Содержание DKG-507























































Отзывы:

Нет отзывов

Похожие инструкции для DKG-507

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: Galaxy Control Systems Страницы: 5

Бренд: IAI Страницы: 5

Бренд: ZIMMERLI MESSTECHNIK Страницы: 12

Бренд: Klimaire Страницы: 5

Бренд: SMC Networks Страницы: 10

Бренд: Gateway Страницы: 2

Бренд: CALEFFI Страницы: 6

Бренд: Oriental motor Страницы: 4

Бренд: Dantherm Страницы: 28

Бренд: Allen-Bradley Страницы: 88

Бренд: Grundfos Страницы: 12

CIMR-VC*****H**-00 series

Бренд: YASKAWA Страницы: 32

AN-X4-ABRIO-HMI

Бренд: QTS Страницы: 48

TRILOGY T500 Series

Бренд: Eclipse Страницы: 20

MotorController WCC 310 UL

Бренд: Window Master Страницы: 39

Бренд: Samson Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды