Datakom DK-70 Скачать руководство пользователя страница 95

Страница: 95 / 121

- 95 -

COMMAND

DESCRIPTION

RESPONSE

GET IP

If GPRS connection is active,
the IP address of the
connection is sent.

GPRS 1

GPRS connection enabled.

GPRS 0

GPRS connection disabled.

RESET
ALARMS

Dismisses the alarms on the
device. Operation mode is not
changed.

REBOOT

The unit switches off and on
again

No response

RESET MODEM

The modem of the unit
switches off and on again

No response

FORCE STOP

The unit enters STOP mode.

FORCE RUN

The unit enters RUN mode.

OUT1 ON

Set remote controlled output
#1 to active state.

OUT1 OFF

Set remote controlled output
#1 to passive state.

OUTxx ON

Set remote controlled output
#xx to active state. (xx denotes
any number between 1 and
16)

OUTxx OFF

Set remote controlled output
#xx to passive state. (xx
denotes any number between
1 and 16)

User Output xx =
OFF

User Output xx = ON

User Output 1 = OFF

Unit forced to RUN!

User Output 1 = ON

Unit forced to STOP!

SMS messages are only accepted from phone numbers set in

SMS1-2-3-4

PHONE NUMBERS

parameters.

Responses to SMS messages are sent to all recorded numbers.

SMS messages must be sent exactly as below, without spaces.

Only

CAPITAL LETTERS

must be used.

Alarms cleared!

GPRS disabled!

GPRS enabled!

IP: 188.41.10.244

19. SMS COMMANDS

Содержание DK-70


























































































































Результаты поиска

Содержание DK-70

Отзывы:

Похожие инструкции для DK-70

Бренды по названию

Популярные бренды

Datakom DK-70, Руководство пользователя

Результаты поиска

Содержание DK-70

Отзывы:

Похожие инструкции для DK-70

Бренды по названию

Популярные бренды