Datakom DK-70 Скачать руководство пользователя страница 43

Страница: 43 / 121

- 43 -

STATUS LEDS:

LINE (MAIN RELAY)

: If RUN mode is selected and there are no conditions to prevent the

compressor from starting, the main relay engages and this LED turns on.

LOAD (LOAD RELAY)

: If the load relay is engaged (the compressor is running under load and

generating compressed air) this LED turns on.

ALARM:

If an alarm condition occurs, this LED turns on.

SERVICE REQUEST:

If one of the service counters expires, this LED turns on.

PROGRAMMABLE LEDS:

The controller offers 2 LEDs which can be user defined. Any alarm, input or

relay function can be assigned to these LEDs.

MODE LEDS:

The relevant LED turns on when a mode is selected either from the physical device or

remotely.

7.5. LED LAMPS

Alarm indicator

STOP mode
indicator

Service
request
indicator

RUN mode
indicator

LINE
(MAIN relay)
status indicator

LOAD
(Load relay)
status
indicator

Programmable
LED indicators

Содержание DK-70


























































































































Результаты поиска

Содержание DK-70

Отзывы:

Похожие инструкции для DK-70

Бренды по названию

Популярные бренды

Datakom DK-70, Руководство пользователя

Результаты поиска

Содержание DK-70

Отзывы:

Похожие инструкции для DK-70

Бренды по названию

Популярные бренды