Datakom DK-70 Скачать руководство пользователя страница 9

Страница: 9 / 121

- 9 -

Before installation:

▪

Read the user manual carefully; determine the correct connection diagram.

▪

Remove all connectors and mounting brackets from the controller, then pass the controller

through the mounting opening.

▪

Place the mounting brackets and tighten. Do not tighten too much, this can break the enclosure.

▪

Make electrical connections with plugs removed from sockets, then place plugs into their sockets.

▪

Be sure that adequate cooling is provided.

▪

Be sure that the temperature of the environment will not exceed the maximum operating

temperature in any case.

Below conditions may damage the device:

▪

Incorrect connections.

▪

Incorrect power supply voltage.

▪

Voltage at measuring terminals beyond the specified range.

▪

Voltage at digital inputs beyond the specified range.

▪

Current through measuring terminals beyond the specified range.

▪

Overload or short circuit at relay outputs.

▪

Connecting or disconnecting data terminals while the device is powered on.

▪

High voltage applied to communication ports.

▪

Ground potential differences at non-isolated communication ports.

▪

Excessive vibration, direct installation on vibrating parts.

Below conditions may cause abnormal operation:

▪

Power supply voltage below minimum acceptable level.

▪

Power supply frequency out of specified limits.

▪

Incorrect phase order of voltage inputs.

▪

Current transformers not matching relevant phases.

▪

Incorrect current transformer polarity.

Current transformers must be used for current
measurement.

No direct connection allowed.

1. INSTALLATION INSTRUCTIONS

Содержание DK-70


























































































































Результаты поиска

Содержание DK-70

Отзывы:

Похожие инструкции для DK-70

Бренды по названию

Популярные бренды

Datakom DK-70, Руководство пользователя

Результаты поиска

Содержание DK-70

Отзывы:

Похожие инструкции для DK-70

Бренды по названию

Популярные бренды