Datakom D-500 MK3 Скачать руководство пользователя страница 131

Страница: 131 / 197

D-500 MK3 User Manual Firmware V-7.5

- 131 -

Parameter Definition

Factory Set

Description

Mail Account Name

d500_a

This is the account name appearing in the

“

from

” tab

of the e-mail recipient. (ex: [email protected])

Mail Account
Password

d500_1234

This is the e-mail password of above e-mail account.

Mail Server Address

smtp.mail.yahoo.com

This is the Outgoing Mail Server Address of the above
e-mail account (ex: smtp.gmail.com)

E-mail Address-1
E-mail Address-2
E-mail Address-3

-
-
-

These are e-mail recipient addresses where the unit is
intended to send e-mail messages. Up to 3 e-mails can
be sent at once.

Parameter Definition

Unit

Min

Max

Factory

Set

Description

Web Programming
Enable

Web programming disabled

Web programming enabled

Web Control Enable

Web control disabled

Web control enabled

Web Refresh Rate

sec

240

The unit will refresh the web page with
this interval.

Ping Period

min

240

The unit will check the availability of the
internet connection with this interval.

Rainbow Refresh Rate

sec

65535

The unit will update the distant
monitoring terminal with this rate.

Rainbow Address-1 Port

65535

This is the port number of the first
monitoring terminal address.

Rainbow Address-2 Port

65535

This is the port number of the second
monitoring terminal address.

Web Server Port

65535

This is the port number of the internal
web server. The unit will answer queries
to this port only.

Modbus TCP/ Port

65535

502

This is the port number of the internal
Modbus TCP/IP terminal. The unit will
answer Modbus requests to this port
only.

SMTP Port

65535

587

This is the port number used for e-mail
sending.

Ethernet Enable

ethernet port disabled

ethernet port enabled

E-mail on IP Change

This parameter controls e-mail sending
when IP address of GPRS or ethernet
connection is changed. No warnings
generated.

no e-mail on IP change

e-mail sent on IP change

17.14. ETHERNET PARAMETERS (continued)

Below ETHERNET related parameters are found in the
Controller Configuration group.

Содержание D-500 MK3






































































































































































































Результаты поиска

Содержание D-500 MK3

Отзывы:

Похожие инструкции для D-500 MK3

Бренды по названию

Популярные бренды

Datakom D-500 MK3, Руководство пользователя

Результаты поиска

Содержание D-500 MK3

Отзывы:

Похожие инструкции для D-500 MK3

Бренды по названию

Популярные бренды