Datakom D-500 MK3 Скачать руководство пользователя страница 94

Страница: 94 / 197

D-500 MK3 User Manual Firmware V-7.5

- 94 -

enter the program mode

, press together

◄

MENU

and

MENU

►

buttons for 5 seconds.

When the program mode is entered, below password entry screen will be displayed.

A 4 digit password must be entered using

▼,

▲

, MENU

►

and

◄

MENU

buttons.

The

▼,

▲

buttons modify the value of the current digit. The

MENU

►,

◄

MENU

buttons navigate

between digits.

The unit supports 3 password levels. The level_1 is designed for field adjustable parameters. The level_2
is designed for factory adjustable parameters. The level_3 is reserved. It allows recalibration of the unit.

The password level-

1 is factory set to ‘

1234

’ and the password level-2 is factory set to ‘

9876

’.

If a wrong password is entered, the unit will still allow access to the program parameters, but in read-only
mode.

If pa

ssword “0000” is entered, only EVENT LOG file will be available.

Passwords are not front panel adjustable.

16.2. ENTERING THE PROGRAMMING MODE

Press 2
buttons
for 5
seconds

Содержание D-500 MK3






































































































































































































Результаты поиска

Содержание D-500 MK3

Отзывы:

Похожие инструкции для D-500 MK3

Бренды по названию

Популярные бренды

Datakom D-500 MK3, Руководство пользователя

Результаты поиска

Содержание D-500 MK3

Отзывы:

Похожие инструкции для D-500 MK3

Бренды по названию

Популярные бренды