Each value / measurement readout parameter selected in
0-20 Display Line 1.1 Small
to
0-24 Display Line 3 Large
has
its own scale and number of digits after a possible decimal
point. Larger numeric values are displayed with few digits
after the decimal point.
Ex.: Current readout 5.25 A; 15.2 A 105 A.
Status display I
This read-out state is standard after start-up or initiali-
zation.
Use [INFO] to obtain information about the value/
measurement linked to the displayed operating variables
(1.1, 1.2, 1.3, 2, and 3).
See the operating variables shown in the display in this
illustration. 1.1, 1.2 and 1.3 are shown in small size. 2 and
3 are shown in medium size.
S ta tus
0.0%
0.0%
0°C
3(3)
1.3
3
2
1.2
1.1
0A
0A
O t op
130BB469.10
Status display II
See the operating variables (1.1, 1.2, 1.3, and 2) shown in
the display in this illustration.
In this example the small readout are: Power Factor in the
upper left corner (position 1.1). THiD of Current in the
middle top (position 1.2), The mains current is displayed in
the upper right corner (1.3). Large readouts are the Output
current (position 2) and lastly underneath the mains
frequency is the reactive current at position 3.
1.1, 1.2 and 1.3 are shown in small size. 2 is shown in large
size.
1.1 Power Factor
1.2 THD of Current [%]
1.3 Mains Current [A]
2 Output Current [A]
3 Mains Frequency
Info:
130BB470.10
Status:
Bottom section
always shows the state of the unit in Status mode.
Top section
Middle section
Bottom section
Status
43 RPM
1.4 Hz
Auto Remote Running
! Pwr.card temp (W29)
2.9%
5.44 A
25.3kW
1(1)
130BP074.10
!
Display contrast adjustment
Press [status] and [
▲
] for darker display
Press [status] and [
▼
] for brighter display
Indicator lights (LEDs):
If certain threshold values are exceeded, the alarm and/or
warning LED lights up. A status and alarm text appear on
the control panel.
The On LED is activated when the unit receives power
from mains voltage, a DC bus terminal, or an external 24 V
supply. At the same time, the back light is on.
•
Green LED/On: Control section is working.
•
Yellow LED/Warn.: Indicates a warning.
•
Flashing Red LED/Alarm: Indicates an alarm.
On
Warn.
Alarm
130BP044.10
LCP keys
Menu keys
The menu keys are divided into functions. The keys below
the display and indicator lamps are used for parameter set-
up, including choice of display indication during normal
operation.
130BP045.10
Status
Quick
Menu
Main
Menu
Alarm
Log
[Status]
Indicates the status of the filter. Use the [Status] key to
toggle single or double readout mode - 5 line readouts, 4
line readouts.
Use [Status] for selecting the mode of display or for
changing back to Display mode from either the Quick
Menu mode, the Main Menu mode or Alarm mode.
[Quick Menu]
Allows quick set-up of the unit. The most common
functions can be programmed here.
The [Quick Menu] consists of:
-
Q1: My Personal Menu
-
Q2: Quick Setup
-
Q5: Changes Made
-
Q6: Loggings
The Quick Menu parameters can be accessed immediately
unless a password has been created via
0-60 Main Menu
Password
,
0-61 Access to Main Menu w/o Password
or
.
It is possible to switch directly between Quick Menu mode
and Main Menu mode.
[Main Menu]
is used for programming all parameters.
The Main Menu parameters can be accessed immediately
unless a password has been created via
0-60 Main Menu
Password
,
0-61 Access to Main Menu w/o Password
How to Operate the Active F...
VLT Active Filter AAF 00x
MG.90.V2.02 - VLT® is a registered Danfoss trademark
45
5
5
