background image

Service guide 

|

 

Disassembling and Assembling, iSave 50-70

© Danfoss | DCS (im) | 2016.10

14 | 180R9387 | 521B1430 | DKCFN.PI.013.1H.02

8.  Mount the 2 x M6 nuts, 2 x M6 washers  

 

and bushings for valve plate on the 2 x M6  

 

screws and then mount them (only by  

 

hand) in the holes with the undercut.  

 

Mount 2 x M16 washers equally between  

 

the 2 screws at the big shaft end.

7.  Lubricate the back-up rings, O-rings and  

 

the holes in the cylinder barrel with clean  

 

filtered water. Place the valve plates with  

 

the 2 holes with the undercut over the 2  

 

thread holes in the cylinder barrel.

10. Remove the exchanger housing from the 

 

port flange by carefully using a plastic 

 

hammer and remove the small pin. 

 

(The pin may fall out).

11. Remove the port plate from the 2 clips  

 

using a screwdriver.

12. Visually check the port plate for wear and 

 

scratches using a straight edge ruler 

 

across the sealing surfaces and replace if 

 needed.

9.  Cross tighten the 2 x M6 nuts to press  

 

down the valve plates equally. The valve  

 

plate at the small shaft end should be  

 

pressed all the way in until you feel a small  

 

resistance (max. 10 Nm). The valve plate  

 

at the big shaft end should only be  

 

pressed in until it is still possible to  

 

remove the 2 x M16 washers (2-3 mm  

 

space left).Remove the 2 x M6 screws with  

 

the nuts, washers and the bushings for  

 

valve plate.

 

Содержание iSave 50-70





























Отзывы: