background image

Service guide 

|

 

Disassembling and Assembling, iSave 50-70

© Danfoss | DCS (im) | 2016.10

16 | 180R9387 | 521B1430 | DKCFN.PI.013.1H.02

WARNING:

Do not use silicone when assembling the 

iSave. Do not reuse disassembled O-rings and 

the shaft seal as they might be damaged. 

Always use new O-rings.

Important: 

It is essential that the pump is serviced in 

conditions of absolute cleanliness. All

parts must be completely clean before 

mounting.

Lubrication:
  •   To prevent seizing-up, lubricate all 

threads.

  •   It is important to lubricate ALL parts 

to be assembled with clean filtered 

water (Especially all PEEK parts).

5.  Assembling the 

 

pressure exchanger

1.  Lubricate the port flange and port plate 

 

with clean filtered water. 

 

Mount the port plate (brine) over the new 

 

clips and pins on the port flange. 

 

Make sure that the clips are below the  

  port flange surface.

3.  Mount the lifting eye on the cylinder  

 

barrel big shaft end and carefully lower the  

 

cylinder barrel straight into the exchanger  

 

housing using lifting equipment. (The  

 

weight of the cylinder barrel is about 32  

 kg).
 

Afterwards remove the lifting eye.

 WARNING: 
  If the cylinder barrel is dropped or 

  lowered too fast into housing, the 

  bearing in the Port flange might be 

  damaged. Replacement can only be 

  done at Danfoss, DK-Nordborg.

2.  Check that the new small pin is still  

 

placed in the port flange and place the 

 

exchanger housing carefully over the 

 

small pin.

Содержание iSave 50-70





























Отзывы: