FCM 300 Series
105
MG.03.B6.02 - VLT is a registered Danfoss trademark
Data read-out: FC therm. ............................... 65
Data read-out: Feedback ............................... 65
Data read-out: Frequency .............................. 65
Data read-out: Inv. temperature ...................... 68
Data read-out: Motor voltage .......................... 66
Data read-out: Power, HP .............................. 66
Data read-out: Power, kW .............................. 66
Data read-out: Reference % .......................... 65
Data read-out: Reference unit ........................ 65
Data read-out: Status word, binary ................. 67
Data read-out: Terminal 1, analogue input ....... 69
Data read-out: Terminal 2, analogue input ....... 69
Data read-out: Torque .................................... 66
Data read-out: Warning word, 1 ..................... 68
Data read-out: Warning word, 2 ..................... 68
DC brake cut-in frequency .............................. 45
DC braking time ............................................. 45
DC braking voltage ......................................... 45
DC-brake ....................................................... 63
Display line 1.1 ............................................... 41
Display line 1.2 ............................................... 41
Display line 1.3 ............................................... 41
Display line 2 .................................................. 40
Display scaling of motor frequency .................. 40
Fault log: Error code ....................................... 70
Fault log: Time ................................................ 70
Fault log: Value ............................................... 71
Flying start ..................................................... 62
Frequency bypass 1 ....................................... 51
Frequency bypass, bandwidth ......................... 51
Function after time out .................................... 52
Jog frequency ................................................ 50
Jog ramp time ................................................ 49
Language ....................................................... 38
LCP copy ....................................................... 40
Local Control/Configuration ............................. 42
Local jog ........................................................ 43
Local reference .............................................. 38
Local reset of trip ............................................ 43
Local reversing ............................................... 43
Local stop ...................................................... 42
Local/remote control ...................................... 38
Lock for data change ..................................... 43
Max. output frequency .................................... 48
Maximum feedback ........................................ 59
Maximum reference ........................................ 48
Min. output frequency ..................................... 47
Minimum feedback ......................................... 59
Minimum reference ......................................... 48
Motor current ................................................. 44
Motor database identification .......................... 72
Motor frequency ............................................. 44
Motor power .................................................. 44
Motor voltage ................................................. 44
Nameplate: Application option type ................. 72
Nameplate: Communication option type .......... 72
Nameplate: Database identification no. ........... 72
Nameplate: FC type ....................................... 71
Nameplate: Software version no. .................... 71
Operating data: Hours run .............................. 69
Operating data: Number of overtemperatures .. 70
Operating data: Number of overvoltages ......... 70
Operating data: Number of power-up’s ........... 69
Operating data: Operating hours ..................... 69
Operating mode (OPERATION MODE) ............ 71
Operating state at power up, local control ....... 43
Overmodulation function ................................. 59
Parameter number (PNU) ................................ 77
Preset reference 1 .......................................... 50
Preset reference 2 .......................................... 50
Process PID anti windup ................................. 60
Process PID diff. gain limit ............................... 61
Process PID differentiation time ....................... 61
Process PID integral time ................................ 61
Process PID lowpass filter time ....................... 62
Process PID Normal/inverse control ................. 60
Process PID proportional gain ......................... 61
Process PID start frequency ............................ 60
Programming Setup ........................................ 39
Quick stop ramp-down time ........................... 49
Quick-stop ..................................................... 63
Ramp-down time 1 ........................................ 49
Ramp-up time 1 ............................................. 49
Rated motor speed ........................................ 45
Reference function ......................................... 50
Reference/feedback range ............................. 48
Reset function ................................................ 58
Reset of hours-run counter ............................. 71
Reversing ....................................................... 63
Rotation direction ........................................... 47
Selection of Setup .......................................... 63
Selection of speed .......................................... 63
Slip compensation .......................................... 46
Start .............................................................. 63
Start compensation .................................. 46, 47
Start voltage ................................................... 45
Switching frequency ....................................... 58
Switching pattern ........................................... 62
Telegram profile .............................................. 64
Terminal 1, analogue input current .................. 52
Terminal 1, max. scaling ................................. 55
Terminal 2, analogue/digital input ..................... 53
Terminal 2, max. scaling ................................. 56
Terminal 2, min. scaling .................................. 55
Terminal 3, digital input .................................... 53
Terminal 4, digital input .................................... 53
Terminal 5, digital input .................................... 53
Terminal 9, output functions ............................ 56
Time out ........................................................ 52
Torque characteristics ..................................... 44
U/f ratio .......................................................... 46
Unit identification for communication ............... 72
Variable switching frequency ........................... 58
PC software for serial communication ................. 74
Periodic maintenance of motor part .................... 25
Plug kit .............................................................. 35
Index
