Danfoss ECL Comfort 110 Скачать руководство пользователя

Страница: 47 / 52

VI.KT.G6.02 © Danfoss | 2016.05 | 47

Definitions

Comfort operation
Normal temperature in the system controlled by the schedule. During heating the flow

temperature in the system is higher to maintain the desired room temperature. During

cooling the flow temperature in the system is lower to maintain the desired room

temperature.

Comfort temperature
Temperature maintained in the heating / DHW circuit during comfort periods.

Desired flow temperature
Temperature calculated by the controller on basis of the outdoor temperature and

influences from the room and / or return temperatures. This temperature is used as a

reference for the control.

Desired room temperature
Temperature which is set as the desired room temperature. The temperature can only be

controlled by the ECL Comfort controller if a room temperature sensor is installed.

If a sensor is not installed, the set desired room temperature however still influences the

flow temperature.

In both cases the room temperature in each room is typically controlled by radiator

thermostats / valves.

Desired temperature
Temperature based on a setting or a controller calculation.

DHW circuit
The circuit for heating the domestic hot water (DHW).

Factory settings
Settings stored in the controller to simplify the setup of your controller the first time.

Flow / DHW temperature
Temperature measured in the flow at any time.

Heating circuit
The circuit for heating the room / building.

Heat curve
A curve showing the relationship between actual outdoor temperature and required

flow temperature.

Содержание ECL Comfort 110





















































Результаты поиска

Содержание ECL Comfort 110

Отзывы:

Похожие инструкции для ECL Comfort 110

Бренды по названию

Популярные бренды

Danfoss ECL Comfort 110, Руководство по эксплуатации

Результаты поиска

Содержание ECL Comfort 110

Отзывы:

Похожие инструкции для ECL Comfort 110

Бренды по названию

Популярные бренды