Danfoss ECL Comfort 110 Скачать руководство пользователя | Manualshive

Страница: 7 / 52

background image

VI.KT.G6.02 © Danfoss | 2016.05 | 7

Daily use

Temperatures

Push any button to switch on the backlight.

Mode COMFORT

Temp. 19 <

Setting the desired room temperature

Change the desired temperature.

The setting of the desired room temperature is important even if a room temperature sensor
/ room panel / remote control is not connected.
Is the room temperature too low?
Make sure that the radiator thermostat(s) does not limit the room temperature.
If you still cannot obtain the desired room temperature by adjusting the radiator
thermostats, the flow temperature is too low. Increase the desired room temperature.

Temperature overview

2 sec.

Push the button to see the sensor (S1-S4) temperatures.

Change between the temperature displays:

S1:

Actual outdoor temperature

Accumulated outdoor temperature

S1 acc. T 12@

S1 act. T 13@

S2:

Actual room temperature

Desired room temperature

S2 des. T 21@

S2 act. T 20@

S3:

Actual flow temperature

Desired flow temperature

S3 des. T 42@

S3 act. T 43@

S4:

Actual return temperature

Desired return temperature limitation

S4 lim. T 30@

S4 act. T 28@

«
...
5
6
7
8
9
...
»

Содержание ECL Comfort 110





















































Отзывы:

Нет отзывов

Похожие инструкции для ECL Comfort 110

Бренд: Bartlett Страницы: 30

Бренд: unicore Страницы: 25

Бренд: unicore Страницы: 24

Бренд: Garmin Страницы: 12

Бренд: Balboa Страницы: 12

Бренд: Paoli Страницы: 16

Бренд: Kasco Страницы: 3

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 20

Бренд: National Instruments Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды