Danfoss ECL Comfort 110 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 52

background image

VI.KT.G6.02

30 | © Danfoss | 2016.05

Maintenance

P1 heat T (heat demand)

7078

Setting range

Factory setting

5 ... 40 °C

20 °C

When the desired flow temperature is above the set temperature in ‘P1 heat T’, the controller

automatically switches ON the circulation pump to meet the heat demand.

5 ... 40: The circulation pump is ON above the set value.

The valve is fully closed as long as the pump is not switched on.

Standby T (standby temperature)

7093

Setting range

Factory setting

5 ... 40 °C

10 °C

Set the desired flow temperature at standby (e.g. during total stop).

5 ... 40: Desired standby flow temperature.

Ext. (external override)

7141

Setting range

Factory setting

OFF / SETBACK / COMFORT

OFF

Choose mode for ‘Ext.’ (external override).

The override can be activated for setback or comfort mode. For override, the controller

mode must be AUTO (scheduled operation).

OFF:

The controller's schedule is not overridden.

SETBACK:

The controller is in setback mode when terminals 11 and 12

are short-circuited.

COMFORT:

The controller is in comfort mode when terminals 11 and 12

are short-circuited.

«
...
28
29
30
31
32
...
»

Содержание ECL Comfort 110





















































Отзывы:

Нет отзывов

Похожие инструкции для ECL Comfort 110

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: Hardi Страницы: 2

Бренд: YASKAWA Страницы: 64

Бренд: V2 Страницы: 3

Бренд: Campbell Страницы: 8

Бренд: Häfele Страницы: 2

Бренд: Häfele Страницы: 24

Бренд: Yamaha Страницы: 92

Бренд: SYR Страницы: 2

Бренд: OJ Electronics Страницы: 8

Бренд: Safety Clamps Страницы: 16

Бренд: Case IH Страницы: 81

Бренд: Cardin Elettronica Страницы: 56

Бренд: Quickie Страницы: 108

Бренд: GARDINER TECHNOLOGY Страницы: 28

Бренд: Zencontrol Страницы: 2

Бренд: Gasboy Страницы: 119

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды