Danfoss ECL Comfort 110 Скачать руководство пользователя | Manualshive

Страница: 16 / 52

background image

VI.KT.G6.02

16 | © Danfoss | 2016.05

Maintenance

This limitation is based on a PI regulation where P (Gain) responds quickly to deviations

and I (Intgr. time) responds slower and over time removes the small offsets between the

desired and actual values. This is done by changing the desired flow temperature.

Intgr. time (time constant for room temp.)

3015

Setting range

Factory setting

OFF / 1 ... 50

OFF

Controls how fast the room temperature adapts to the desired room temperature (I control).

OFF: The control function is not influenced by the ‘Intgr. time’.
1:

The desired temperature is adapted quickly.

50:

The desired temperature is adapted slowly.

Gain - max. (room temp. limitation, max.)

3182

Setting range

Factory setting

-9.9 ... 0.0

-4.0

Determines how much the flow temperature will be influenced (decreased) if the room temperature is

higher than the desired room temperature (P control).

-9.9: The room temperature has a big influence.
0.0:

The room temperature has no influence.

Gain - min. (room temp. limitation, min.)

3183

Setting range

Factory setting

0.0 ... 9.9

0.0

Determines how much the flow temperature will be influenced (increased) if the room temperature is

lower than the desired room temperature (P control).

0.0:

The room temperature has no influence.

9.9:

The room temperature has a big influence.

«
...
14
15
16
17
18
...
»

Содержание ECL Comfort 110





















































Отзывы:

Нет отзывов

Похожие инструкции для ECL Comfort 110

Бренд: Nelson Страницы: 19

Бренд: C-TEC Страницы: 2

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

Бренд: Aalborg Страницы: 128

Бренд: Radarcan Страницы: 40

Бренд: Yardney Страницы: 8

Бренд: Easy-Laser Страницы: 84

Бренд: Easy Heat Страницы: 4

Бренд: Parker Страницы: 28

Бренд: VAT Страницы: 39

Бренд: Samson Страницы: 124

Бренд: Samson Страницы: 86

Бренд: VAC Страницы: 5

Бренд: KIPI Страницы: 44

Бренд: Gallagher Страницы: 2

OPTISWITCH 5100 C

Бренд: KROHNE Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды