manualshive.com logo in svg

Danfoss ECL Comfort 110, Руководство по эксплуатации

Danfoss ECL Comfort 110 - надежный термостат для управления отоплением в вашем доме. Скачайте бесплатно руководство по монтажу и эксплуатации с нашего manualshive.com. Этот удобный и энергоэффективный продукт обеспечит комфорт и уют в вашем доме.

Поделиться
Скачать
background image

 VI.KT.G6.02

32 | © Danfoss |  2016.05 

Maintenance

0:   

The controller works as slave. The slave receives information about the  

  outdoor temperature (S1), system time, and signal for DHW demand in  

  the master.

1 ... 9:     The controller works as slave. The slave receives information about  

  the outdoor temperature (S1), system time, and signal for DHW    

  demand in themaster. The slave sends information about the desired  

  flow temperature to the master.

10 ... 14:   Not used.
15:  

  The controller is master. The master sends information about the   

  outdoor temperature (S1) and system time. The ECL BUS is active and  

  connected ECAs are powered.

The ECL Comfort controllers can be connected via the ECL BUS to perform a larger 

system. The controller, which is physically connected with the outdoor temperature 

sensor, is the master of the entire system and must have the address 15.

Each slave must be configured with its own address (1 ... 9).

However, more slaves can have the address 0 if they only have to receive information  

about outdoor temperature and system time.

Type 7600

Setting range

Factory setting

 116 / 130

130

Use this setting to change your application or restore the factory settings.

116:  Constant temperature control of DHW circuit.

130:  Weather compensated control of heating and boiler systems.

Select the desired application type.

 5 sec.

Start the chosen application.

Factory settings are restored. All personal settings will be deleted. It is recommended to 
make a note of your personal settings in the ‘Settings overview’ for future use.

The application can not be changed from 116 to 130 or vice versa if the ECL Comfort 110 is 
pre-programmed from the substation-builder.

Содержание ECL Comfort 110





















































Отзывы:

Нет отзывов

Похожие инструкции для ECL Comfort 110

Parasound 7100 Owner'S Manual preview
7100
Бренд: Parasound Страницы: 72
Jafar 7010 Operation And Maintenance Manual preview
7010
Бренд: Jafar Страницы: 15
D-Link DWC-2000 Cli Reference Manual preview
DWC-2000
Бренд: D-Link Страницы: 113
D-Link DWC-1000 Reference Manual preview
DWC-1000
Бренд: D-Link Страницы: 146
Jafar 3500 Operating Manual preview
3500
Бренд: Jafar Страницы: 9
Samsung SPC-6000 Quick Setup Manual preview
SPC-6000
Бренд: Samsung Страницы: 6
Samsung SyncMaster VC240 Reference Manual preview
SyncMaster VC240
Бренд: Samsung Страницы: 39
Samsung MWR-WE10N Manual preview
MWR-WE10N
Бренд: Samsung Страницы: 32
Samsung iDCS500 Manual preview
iDCS500
Бренд: Samsung Страницы: 91
Samsung iDCS500 User Manual preview
iDCS500
Бренд: Samsung Страницы: 80
Warren Controls E024 Installation, Operation And Maintenance Instructions preview
E024
Бренд: Warren Controls Страницы: 28
EAS Electric ECRP86EKD Operating Manual preview
ECRP86EKD
Бренд: EAS Electric Страницы: 89
jcm-tech WAVE500 User Manual preview
WAVE500
Бренд: jcm-tech Страницы: 8
National Instruments NI 9215 Calibration Procedure preview
NI 9215
Бренд: National Instruments Страницы: 8
RAKwireless RAK3172 User Manual preview
RAK3172
Бренд: RAKwireless Страницы: 6
Eaton SCD24 Installation Manual preview
SCD24
Бренд: Eaton Страницы: 8
ABB RHDE250 Operating Instruction preview
RHDE250
Бренд: ABB Страницы: 44
Omega CNI16D Quick Start preview
CNI16D
Бренд: Omega Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды