DANA Spicer Torque-Hub S350 Series Скачать руководство пользователя | Manualshive

Страница: 19 / 56

background image

19

Planetary Final Drive Service Manual

1

st

Stage Intermediate Carrier Disassembly

1.

Unbend the tang of Lock-Tanged Washer (2I) from the Bearing Nut (2H) and remove the
Bearing Nut (2H) from the Planet Shaft (2K).

2.

Remove Planet Shaft (2K) from the Carrier (2A).

3.

Remove Lock-Tanged Washer (2I) from the Carrier (2A) and discard it.

4.

Remove Lock Pin (2J) from slot of Carrier (2A).

5.

Slide out the Planet Gear Subassembly from the window of the Carrier (2A).

6.

Remove Thrust Washer (2F) from the window of the Carrier (2A).

7.

Remove both Bearing Cone (2C) from the bore of Planet Gear (2B).

8.

Remove both Bearing Cup (2D) from the bore of Planet Gear (2B).

9.

Remove Thrust Spacer (2E) from the bore of Planet Gear (2B).

CAUTION:

Safety glasses must be worn during these next steps.

10.

Remove Retaining Ring (2G) from internal groove of the Planet Gear (2B).

11.

Repeat the steps 1 through 10 for the remaining two Planet Gears (2B).

This concludes the 1st Stage Intermediate Carrier Disassembly.

«
...
17
18
19
20
21
...
»

Содержание Spicer Torque-Hub S350 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для Spicer Torque-Hub S350 Series

Бренд: D+H Страницы: 16

SLO-SYN TD Series

Бренд: Superior Electric Страницы: 26

Бренд: Fagor Страницы: 406

CMMT-AS-C12-11A-P3-EC-S1

Бренд: Festo Страницы: 16

Бренд: Canworld Страницы: 267

Бренд: Wheatstone Страницы: 207

Бренд: StepperOnline Страницы: 12

Бренд: PR electronics Страницы: 30

Бренд: Nakanishi Страницы: 20

Бренд: QPS Страницы: 16

Бренд: KEB Страницы: 378

Бренд: IBM Страницы: 92

Бренд: Beckhoff Страницы: 72

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 28

Бренд: Shengyi Страницы: 18

IEEE 1394 External DVD-R/RW Drive

Бренд: Ikebana Страницы: 13

ELTRAL KS 30 EASY

Бренд: GU Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды