DANA Spicer Torque-Hub S350 Series Скачать руководство пользователя | Manualshive

Страница: 42 / 56

background image

42

38.

Grease and install Thrust Washer (43) onto the Intermediate Sun Gear (6). The grease
should hold the Washer (43) in place for assembly.

39.

Grease and install O-Ring (36) onto the Cover (5). Insure that the O-Ring (26) is fully seated.

40.

Install Input Carrier Subassembly (3). Insure Input Carrier splines engage with Sun Gear (6)
splines.

41.

Install Ring Gear (45) onto the Cover (5). Align bolt holes in Ring Gear (45) with the Cover
(5) bolt holes. Insure that the Ring Gear (45) is seated against the Cover (5).

42.

Install Sun Gear (42) into the mesh with gear side down. Insure the Sun Gear (42) engages
into the mesh with input planet gears.

NOTE:

Insure the Input Sun Gear (42) aligns with the bore of Thrust Washer (43).

43.

Install the Input Cover Subassembly onto the Ring Gear (45). Align the bolt holes in the
Cover (46) with the holes in the Ring Gear (45).

44.

Apply loclite-243 and Install Hex Bolts (35) on Cover (46) through Ring Gear (45) using
calibrated torque gun in star pattern per standard bolt circle torque procedure, and Torque
Bolts (35) to 80-100 ft-lbs.

45.

The unit should now be leak and roll checked as per instructions on page 5 & 6.

This concludes the Main Assembly.

«
...
40
41
42
43
44
...
»

Содержание Spicer Torque-Hub S350 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для Spicer Torque-Hub S350 Series

Бренд: Vacon Страницы: 38

GA700 GA700 Series

Бренд: YASKAWA Страницы: 32

Бренд: ABB Страницы: 20

Бренд: Samsung Страницы: 11

Бренд: Samsung Страницы: 10

Writemaster SH-S183A

Бренд: Samsung Страницы: 29

Бренд: Samsung Страницы: 23

Бренд: Samsung Страницы: 23

Бренд: Samsung Страницы: 9

Бренд: Samsung Страницы: 26

Бренд: Samsung Страницы: 35

Бренд: Samsung Страницы: 34

Бренд: Samsung Страницы: 34

Бренд: Samsung Страницы: 40

Бренд: Yamaha Страницы: 13

Mobile Drive II

Бренд: Freecom Страницы: 43

Бренд: RIB Страницы: 56

Бренд: RS PRO Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды