DANA Spicer Torque-Hub S350 Series Скачать руководство пользователя | Manualshive

Страница: 40 / 56

background image

40

22.

Lower Sun Gear (23) with spline side up into the output planet gear mesh. Insure Sun Gear
(23) is engaged with planet gears of Output Carrier Subassembly..

23.

Install Spacer (60) onto the Sun gear (23).

24.

Lower Intermediate Carrier Subassembly with internal coupling side down onto sun gear
(23). Insure that the internal coupling splines and the Sun Gear (23) splines are engaged
and Thrust Washer (1L) has seated into bore of Sun Gear (23).

25.

Grease and install O-Ring (25) onto the Ring Gear (18) o-ring groove.

26.

Lower Ring Gear (18) onto the Spacer Housing (29). Align the Ring Gear (18) teeth with the
planet gear teeth of the Intermediate Carrier Subassembly (4). Insure that the reamed
shoulder bolt holes in Ring Gear (18) are aligned with the appropriate tapped holes in
Spacer Housing (29). Insure that the Ring Gear (18) is seated against the Spacer Housing
(29).

CAUTION:

Safety glasses must be worn during these next steps.

27.

Install Retaining Ring (26) onto external retaining ring groove of Sun Gear (7).

28.

Install Sun Gear (7) with spline side up into the intermediate planet gear mesh.

Continued on Next Page

«
...
38
39
40
41
42
...
»

Содержание Spicer Torque-Hub S350 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для Spicer Torque-Hub S350 Series

Бренд: D+H Страницы: 8

Бренд: Danfoss Страницы: 54

Бренд: National Instruments Страницы: 44

Бренд: JVC Страницы: 29

SINAMICS S210 FSA

Бренд: Siemens Страницы: 2

MICROMASTER 6SE92

Бренд: Siemens Страницы: 2

SIMODRIVE POSMO SI

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 6

SIMATIC MICRO-DRIVE

Бренд: Siemens Страницы: 39

1FL3041-0AC31-0BJ0

Бренд: Siemens Страницы: 60

6SL3210-5CC14-0UA0

Бренд: Siemens Страницы: 68

Бренд: Siemens Страницы: 100

Бренд: Siemens Страницы: 112

Бренд: Siemens Страницы: 124

SIMOREG DC Master 6RA7018-6DS22

Бренд: Siemens Страницы: 616

Бренд: Parker Страницы: 74

Бренд: GFA Страницы: 21

Бренд: GFA Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды