DANA Spicer Torque-Hub S350 Series Скачать руководство пользователя | Manualshive

Страница: 22 / 56

background image

22

Planetary Final Drive Service Manual

Input Carrier Disassembly

1.

Unbend the tang of Lock-Tanged Washer (3H) from the Bearing Nut (3G) and remove the
Bearing Nut (3G) from the Planet Shaft (3E).

2.

Remove Planet Shaft (3E) from the Carrier (3A)

3.

Remove Lock-Tanged Washer (3H) from the Planet Shaft (3E) and discard it.

4.

Remove Lock Pin (3D) from slot of Carrier (3A).

5.

Slide out the Planet Gear Subassembly from the window of the Carrier (3A).

6.

Remove Thrust Washer (3B) from the window of the Carrier (3A).

NOTE:

Bearing (3C) is a matched assembly and must be kept as a set unless they are to be

replaced.

7.

Remove both Bearing Cone (3C) from the bore of Planet Gear (3F).

NOTE:

Skip steps 8 and 9 unless the bearing is to be replaced.

8.

Remove both Bearing Cup (3C) from the bore of Planet Gear (3F).

CAUTION:

Safety glasses must be worn during these next steps.

9.

Remove Retaining Ring (3C) from internal groove of the Planet Gear (3F).

10.

Repeat the steps 1 through 9 for the remaining two Planet Gears (2B).

This concludes the Input Carrier Disassembly.

«
...
20
21
22
23
24
...
»

Содержание Spicer Torque-Hub S350 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для Spicer Torque-Hub S350 Series

Бренд: YASKAWA Страницы: 376

CLSM-150-B A Series

Бренд: Ewellix Страницы: 30

Continuous Rotation Servo

Бренд: Parallax Страницы: 9

Бренд: Sprint Electric Страницы: 8

DA- -A20 Series

Бренд: Eaton Страницы: 16

Бренд: Carotron Страницы: 42

Бренд: Label Страницы: 56

Super-writemaster SH-S203N

Бренд: Samsung Страницы: 2

Super-writemaster SH-S203D

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 10

Бренд: Samsung Страницы: 15

SE-S084C - DVD±RW / DVD-RAM Drive

Бренд: Samsung Страницы: 1

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 25

writemaster SE-S164L

Бренд: Samsung Страницы: 28

Бренд: Samsung Страницы: 21

Бренд: Samsung Страницы: 25

Бренд: Samsung Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды