DANA Spicer Torque-Hub S350 Series Скачать руководство пользователя | Manualshive

Страница: 38 / 56

background image

38

NOTE:

Insure not to Grease O-Ring (79) in step below.

7.

Install O-Ring (79) onto the Housing (32) o-ring groove.

8.

Lower Ring Gear (24) onto the Housing (32) by aligning the Ring Gear (24) teeth with the
planet gear teeth of the Output Carrier Subassembly. Insure that the Ring Gear (24)
dowelpin holes are aligned with the dowel pins in housing. Insure that the Ring Gear (24) is
seated against the Housing (32).

9.

Spray the internal components with RP oil.

10.

Place Spacer Housing (29) with flange side up onto the table.

11.

Install Spacer (1) into the spacer slots in Spacer Housing (29).

12.

Apply Loctite-243 and install Flat Head Hex Bolts (51) into the Spacer Housing (29) through
Spacer (1). Torque to 270-280 in-lbs.

13.

Spray the Spacer Housing (29) bushing bore in Spacer Housing (29) with alcohol, then wipe
with a clean rag. Insure there is no debris left in the bore.

14.

Grease and install O-Ring (79) onto the Spacer Housing (29) o-ring groove.

Continued on Next Page

«
...
36
37
38
39
40
...
»

Содержание Spicer Torque-Hub S350 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для Spicer Torque-Hub S350 Series

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 346

Бренд: GRASS Страницы: 19

Megatorque M-EDC-PN2012 Series

Бренд: NSK Страницы: 32

Бренд: Roland Страницы: 2

Бренд: Teac Страницы: 1

Бренд: Becker Страницы: 28

Бренд: Becker Страницы: 32

Бренд: Becker Страницы: 32

Бренд: Honeywell Страницы: 4

Бренд: Honeywell Страницы: 3

Бренд: HNC Electric Страницы: 121

Бренд: Bedford Страницы: 116

Бренд: SAJ Страницы: 30

Бренд: ZF-DUOPLAN Страницы: 34

Бренд: Pepperl+Fuchs Страницы: 2

Бренд: ProMinent Страницы: 32

Бренд: Parker Страницы: 640

Бренд: Bardac drives Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды