DANA Spicer Torque-Hub S350 Series Скачать руководство пользователя | Manualshive

Страница: 39 / 56

background image

39

15.

Lower Spacer Housing (29) onto Ring Gear (24) with flange side down. Align bolts holes in
Spacer Housing (29) with Ring Gear(24) bolt holes. Insure the Spacer Housing (29) has
seated against Ring Gear (24).

16.

Install four Hex Bolts (52) through Washer (53) into the Spacer Housing (29). Torque Bolts
(52) to 680 ft-lbs.

17.

Install O-Ring Plugs (85) into pipe plug holes in Spacer Housing (29).Torque Pliugs to 170-
192 ft-lbs.

NOTE:

Use O-Ring (25) to leak test in the step below for leak test adapter plate.

18.

Install leak test adapter plate tool T-222390 onto the Spacer Housing (29).

19.

Perform air leak test and record the results in QDR.

20.

Remove test adapter plate T-222390.

21.

Apply loctite-243 and install rest of Hex Bolts (52) through Washer (53) into the Spacer
Housing (29). Torque Bolts (52) to 680 ft-lbs.

Continued on Next Page

«
...
37
38
39
40
41
...
»

Содержание Spicer Torque-Hub S350 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для Spicer Torque-Hub S350 Series

Бренд: Eaton Страницы: 16

Бренд: ABB Страницы: 56

ACQ550-CC-011A-6

Бренд: ABB Страницы: 38

Бренд: ABB Страницы: 182

3AXD50000018852

Бренд: ABB Страницы: 38

Бренд: ABB Страницы: 196

Бренд: ABB Страницы: 188

Бренд: ABB Страницы: 222

Бренд: ABB Страницы: 494

Бренд: ABB Страницы: 2

Бренд: CENTENT Страницы: 36

Pentek Intellidrive XL

Бренд: Pentair Страницы: 20

Бренд: UNI Geräte Страницы: 14

Бренд: Shanghai Siheng Motor Страницы: 39

Бренд: Eskridge Страницы: 7

Бренд: Xinje Страницы: 107

Бренд: Leadshine Страницы: 27

Бренд: BLEMO Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды