DANA Spicer Torque-Hub S350 Series Скачать руководство пользователя | Manualshive

Страница: 12 / 56

background image

12

Planetary Final Drive Service Manual

Main Disassembly

1.

Perform a roll check and a leak check prior to disassembling the unit.

2.

Remove the two O-Ring Pipe Plugs (85) and drain the oil out of the gearbox by slightly tilting
the whole Unit.

NOTE:

Record the condition and volume of the oil.

3.

Remove twenty Hex Bolts (35) from the Input Cover (5).

4.

Lift the Cover Subassembly off of the unit.

5.

Remove the O-Ring (36) out of the Unit and Discard it.

6.

Remove the Input Sun Gear (42) out of the Input Carrier Subassembly.

7.

Lift the Input Carrier Subassembly off of the unit.

8.

Remove the Ring Gear (45) out of the Unit.

9.

Remove the Thrust Washer (43) from the Intermediate Sun Gear (6).

10.

Remove the Intermediate Sun Gear (6) out of the unit.

Continued on Next Page

«
...
10
11
12
13
14
...
»

Содержание Spicer Torque-Hub S350 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для Spicer Torque-Hub S350 Series

Бренд: GE Страницы: 86

EcoDrive P40 ED

Бренд: Pfaff Страницы: 28

Бренд: Teac Страницы: 1

Бренд: TOYODenki Страницы: 64

Бренд: Omron Страницы: 8

Бренд: Kobalt Страницы: 95

Бренд: Knightsbridge Страницы: 4

RolloTron Pro Star Series

Бренд: RADEMACHER Страницы: 72

Rolltron PRO comfort

Бренд: RADEMACHER Страницы: 76

Бренд: Metronix Страницы: 171

Бренд: D+H Страницы: 36

Бренд: sauter Страницы: 8

Vincent Associates VMM-D3

Бренд: Uniblitz Страницы: 38

Classic Q3 400 Series

Бренд: Unitek Страницы: 32

Бренд: ZIEHL-ABEGG Страницы: 105

Бренд: ZIEHL-ABEGG Страницы: 200

Бренд: Pacific Digital Страницы: 24

DVD+R/RW Writer

Бренд: Gigabyte Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды