Dalsa Linea ML ML-FM-08K30H Скачать руководство пользователя страница 65

Страница: 65 / 83

Camera Performance and Features

•

Display Name

Feature

Description

Device
Version
& View

Calibrate PRNU

flatfieldCalibrationPRNU

Initiates the PRNU calibration
process

1.00
Beginner
DFNC

Flat Field Correction Current
Active Set

flatfieldCorrectionCurrentActiveSet

Factory Set
User set (1 thru 16)

Selects the User PRNU set to be
saved or loaded.
Factory set can only be loaded.
Only the PRNU values are saved
or loaded which is much faster
than saving or loading the full
Factory or User set.

1.00
Guru
DFNC

Save Calibration

flatfieldCalibrationSave

Saves the User PRNU set
specified by
flatfieldCorrectionCurrentActiveSet
to the camera.

1.00
Guru
DFNC

Load Calibration

flatfieldCalibrationLoad

Loads the User PRNU set
specified by
flatfieldCorrectionCurrentActiveSet
to the camera and makes it active.

1.00
Guru
DFNC

Output LUT Mode

lutMode

Allows the output LUT to be
selected

1.00
Beginner
DFNC

Off

The output LUT is disabled and
linear data is output

Gamma Correction

The output LUT is populated using
the gamma correction equation.

User Defined

LUT uploaded by the user is used.

Gamma Correction

gammaCorrection

The output LUT is populated using
the following gamma correction
equation:

𝐷𝐷𝐷𝐷

𝑜𝑜𝑜𝑜𝑜𝑜

= 255 ×

�

𝐷𝐷𝐷𝐷

𝑖𝑖𝑖𝑖

255

�

𝛾𝛾

1.00
Beginner
DFNC

Image Filter Mode

imageFilterMode

Enable image filter.

Image Filter Type

imageFilterType

Read-only: Weighted Average

Image Filter Kernel Size

imageFilterKernelType

Kernel 1x3 or 1x5

Image Filter Contrast Ratio

imageFilterContrastRatio

0 to 1

Содержание Linea ML ML-FM-08K30H




















































































Результаты поиска

Содержание Linea ML ML-FM-08K30H

Отзывы:

Бренды по названию

Популярные бренды

Dalsa Linea ML ML-FM-08K30H, Руководство пользователя

Результаты поиска

Содержание Linea ML ML-FM-08K30H

Отзывы:

Бренды по названию

Популярные бренды