Dalsa Linea ML ML-FM-08K30H Скачать руководство пользователя | Manualshive

Страница: 41 / 83

background image

Camera Performance and Features

•

41

Those areas of the image where high roll-off is present will show higher noise levels after flat field

calibration due to the higher gain values of the correction coefficients. Flat field calibration can only

compensate for up to an 8:1 variation. If the variation exceeds 8:1 then the line profile after

calibration will include pixels that are below the un-calibrated peak level.

Note:

The Linea ML camera has many different modes of operation. It is strongly recommended that the

camera be flat fielded for that mode of operation that is intended.

Saving & Rapidly Loading a PRNU Set Only

Loading a complete user set takes approximately 800 ms while loading only the user PRNU

coefficients takes less than 200 ms.
Use the User PRNU Set Selector parameter to select the set you want to save or load. 17 sets are

available—16 user and 1 factory. Loading the Factory Set is a good way to clear the user PRNU.
The Factory Set is read-only. Loading the Factory Set is a good way to clear the user PRNU.
Save the current user PRNU coefficients using the “Save User PRNU Set” feature. Load the user

PRNU coefficients from the set specified using the “User PRNU Set Selector” and the “Load User

PRNU Set” command features.

Setting Custom Flat Field Coefficients

Flat Field (PRNU) coefficients can be custom modified and uploaded to the camera. They can also

be downloaded from the camera.

To upload or download coefficients, use File Access Control Category > Upload / Download File >

Settings and then select Miscellaneous > Current PRNU to download / upload a file.

The file format is described in the document 03-084-20133 Linea ML Binary File Format, which can

be obtained from Teledyne DALSA Technical Support. This document also includes Excel spread

sheet examples.

The PRNU coefficients are used by the camera as soon as they are uploaded. To avoid loss at

power up or while changing row settings, the uploaded coefficients should be saved to one of the

available user sets.

Flat Field Calibration Filter

See the section Flat Field Category in Appendix A for GenICam features associated with this section

and how to use them

Related Feature: Calibration Algorithm

If a sheet of material is being used as a white target, it must be completely free of blemishes and

texture.

The presence of dirt or texture will generate a variation in the image that will be incorporated into

the calibration coefficients of the camera. Further, once the target is removed, or moved, vertical

stripes will be present in the scanned image.

Dirt or texture that has dark characteristics will appear as bright vertical lines. Dirt or texture that

has bright characteristics will appear as dark vertical lines.

«
...
39
40
41
42
43
...
»

Содержание Linea ML ML-FM-08K30H




















































































Отзывы:

Нет отзывов

Похожие инструкции для Linea ML ML-FM-08K30H

Бренд: Panasonic Страницы: 15

Бренд: Samsung Страницы: 28

Бренд: SBIG Страницы: 47

Бренд: Olympus Страницы: 124

Бренд: Baumer Страницы: 68

Бренд: XtendLan Страницы: 34

Бренд: LENCO Страницы: 3

Бренд: Polaroid Страницы: 63

Бренд: Omron Страницы: 594

Бренд: CAMMHD Страницы: 24

Бренд: Longse Страницы: 2

VISION NAVICEIVER VNA-RCAM-UNI

Бренд: ESX Страницы: 4

Бренд: Joy Страницы: 14

Бренд: PNI Страницы: 4

Бренд: Targa Страницы: 116

Бренд: VMS Страницы: 4

Бренд: Dignsys Страницы: 66

Бренд: Edimax Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды