Dalsa Linea ML ML-FM-08K30H страница 27 Скачать руководство пользователя

Страница: 27 / 83

Camera Performance and Features

•

Camera Performance and

Features

This section is intended to be a progressive introduction to the features of the camera, including

explanations of how to use them effectively.

A detailed description of all features is found in Appendix A: GenICam Commands.

Synchronizing to Object Motion

Acquiring Images: Triggering the Camera

Related Features: Exposure Mode, Trigger Mode, Trigger Source, Trigger Activation

A number of different methods that can be used to trigger image acquisition in the camera:

Internal Trigger

The simplest method is to set the Trigger Mode to “Internal”. This results in the camera being

triggered by an internal timer, which can be adjusted using the Acquisition Line Rate feature.

External Triggers

When the Trigger Mode command is set to “External”, the triggers to the camera can come from

different sources, set using the Trigger Source feature.

The available sources for the triggers are from pin 5 of the GPIO connector, from the Camera Link

HS frame grabber, or from the rotary encoder feature (using pin 5 and pin 6 of the GPIO

connector).

Use the Trigger Activation feature to select the edge or level that triggers the camera. The options

are: Rising Edge, Falling Edge or Any Edge.

CamExpert can be used to configure the frame grabber for routing the encoder signal from the

frame grabber input to the trigger input of the camera via the Camera Link HS data cable.

Line Rate & Synchronization

A continuous stream of encoder trigger pulses synchronized to the object motion establishes the

line rate. The faster the object’s motion is, the higher the line rate. The camera can accommodate

up to its specified maximum frequency. If the maximum frequency is exceeded, the camera will

continue to output image data at the maximum specified. The result will be that some trigger

pulses will be missed and there will be an associated distortion (compression in the scan direction)

of the image data. When the line rate returns to or below the maximum specified, then normal

imaging will be reestablished.

Содержание Linea ML ML-FM-08K30H




















































































Результаты поиска

Содержание Linea ML ML-FM-08K30H

Отзывы:

Похожие инструкции для Linea ML ML-FM-08K30H

Бренды по названию

Популярные бренды

Dalsa Linea ML ML-FM-08K30H, Руководство пользователя

Результаты поиска

Содержание Linea ML ML-FM-08K30H

Отзывы:

Похожие инструкции для Linea ML ML-FM-08K30H

Бренды по названию

Популярные бренды