Dalsa Linea ML ML-FM-08K30H страница 12 Скачать руководство пользователя

Страница: 12 / 83

•

Linea ML Multiline Monochrome / HDR CMOS Cameras

Figure 3. Linea ML Dual LC/SFP+ Connector Configuration

The ML-HM camera model uses a CX4 connector for the output—using up to 5 lanes.

Figure 4. Single CLHS Connector Configuration

The command channel is used by the frame grabber to send commands, configuration and

programming data to the camera and to receive command responses, status, and image data from

the camera. With two SFP+ modules populated, the CLHS protocol will auto negotiate which one

will be dedicated as the command channel. Data and command transmission is done with CLHS X

protocol (64b / 66b) at the default speed of 10 Gbs.

Data Cables

LC Fiber Optic (ML-FM Cameras)

The fiber optic cables for the ML-FM camera models require LC connections on both ends of the

cable. The frame grabber requires the LC connector to be plugged into a SFP+ transceiver module.

LC is a small-form factor fiber optic connector that uses a 1.25 mm ferrule, half the size of a

standard connector. These cables are in wide use in the telecommunications industry and available

in many lengths.

The distance through which the data can be transmitted depends on the type of fiber optic used.

Recommended fiber optic cables are types OM3 and OM4.

RXC

TXC

TX1

TX2

TX3

TX4

TX5

TX6

TXC

RXC

RX1

RX2

RX3

RX4

RX5

RX6

Data Lane 6

Data Lane 0

Command

Channel

Video

Channel

Link

Camera

(C2,7M1)

Frame Grabber

(C2,7M1)

Содержание Linea ML ML-FM-08K30H




















































































Результаты поиска

Содержание Linea ML ML-FM-08K30H

Отзывы:

Похожие инструкции для Linea ML ML-FM-08K30H

Бренды по названию

Популярные бренды

Dalsa Linea ML ML-FM-08K30H, Руководство пользователя

Результаты поиска

Содержание Linea ML ML-FM-08K30H

Отзывы:

Похожие инструкции для Linea ML ML-FM-08K30H

Бренды по названию

Популярные бренды