manualshive.com logo in svg

Dalsa Linea ML ML-FM-08K30H, Руководство пользователя

Поделиться
Скачать
Dalsa Linea ML ML-FM-08K30H Скачать руководство пользователя страница 48

 

48  

•

 

Camera Performance and Features  

10.

 

This file can loaded into the camera using the 

File Access

 features. It is saved with the current 

Load / Save Configuration

 user set; ensure that a user set and not the factory set is selected, 

otherwise the upload will fail. 

11.

 

Deselect the 

Lookup Table 

|

 Enable

 feature. 

12.

 

Return CamExpert to 

Pixel Depth

 = 8, and 

Image Buffer

 = 8 bits. 

 

Important points: 

•

 

The frame grabber must be configured mono 12 bits in, 16 bits out. 

•

 

In the Parameters explorer a frame grabber feature must be selected, not a camera feature. 

•

 

The Lookup table must be enabled to be created. But should be disabled to use the camera 

LUT. 

Adjusting Responsivity and Contrast Enhancement 

See the section Camera Control Category in Appendix A for GenICam features associated with this 

section and how to use them. 

 

Related Features: Gain Selector, Gain, Offset 

 

It is best for camera performance to always use the maximum exposure time possible based on the 

maximum line rate of the inspection system and any margin that may be required to accommodate 

illumination degradation. However, it will be necessary to adjust the responsivity to achieve the 

desired output from the camera. The camera has a gain feature that can be used to adjust the 

camera’s responsivity. 

 

Gain adjustment is available to independently adjust each line or all of them together. System Gain 

can be adjusted from 1 to 10x. Individual line gains can be adjusted from 1 to 4x. 

 

When an image contains no useful dark image data below a specific threshold, then it may be 

beneficial to increase the contrast of the image. 

 

The camera has an offset feature that allows a specified level to be subtracted from the image 

data. The gain feature can then be used to return the peak image data to near output saturation 

with the result being increased image contrast. 

 

First, determine the offset value you need to subtract from the image with the current gain setting 

you are using. Then set this as a negative offset value and apply additional gain to achieve the 

desired peak image data values. 

 

Note: A positive offset value is not useful for contrast enhancement. However, it can be used while 

measuring the dark noise level of the camera to ensure zero clipping is not present. 

Содержание Linea ML ML-FM-08K30H




















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды