Dalsa Linea ML ML-FM-08K30H Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 83

Dalsa Linea ML ML-FM-08K30H Скачать руководство пользователя страница 61

Camera Performance and Features

•

61

Digital I/O Control Feature Descriptions

Display Name

Feature

Description

Device
Version
& View

Trigger Mode

TriggerMode

Internal

External

Determines the source of trigger to the camera,
internal or external

1.00
DFNC
Beginner

Trigger Source

TriggerSource

CLHS In

Rotary Encoder

GPIO1

Determines the source of external trigger

Source of trigger is from the frame grabber

Source of trigger is from the two shaft encoder
inputs

Source of trigger is from Line 1 of the GPIO
connector

1.00
DFNC
Beginner

Trigger Input Line
ActivationEdge

TriggerActivation

RisingEdge

FallingEdge

AnyEdge

Determines which edge of a input trigger will activate
on. The two inputs are XOR’d together when Shaft
Encoder is selected to provide a single signal.

The trigger is considered valid on the rising edge of
the line source signal (after any processing by the
line inverter module).

The trigger is considered valid on the falling edge of
the line source signal.

The trigger is considered valid on any edge

1.00
DFNC
Beginner

Rotary Encoder Direction

Counter Clockwise

Clockwise

rotaryEncoderDirection

CounterClockwise

Clockwise

Specifies the phase which defines the encoder
forward direction

Inspection goes forward when the rotary encoder
direction is counter clockwise (phase A is ahead of
phase B)

Inspection goes forward when the rotary encoder
direction is clockwise (phase B is ahead of phase A)

1.00
DFNC
Beginner

Rotary Encoder Output
Mode

rotaryEncoderOutputMode

Position

Motion

Specifies the conditions for the Rotary Encoder
interface to generate a valid Encoder output signal.

Triggers are generated at all new position
increments in the selected direction. If the encoder
reverses no trigger events are generated until it has
again passed the position where the reversal
started.

The triggers are generated for all motion increments
in either direction.

1.00
DFNC
Beginner

Input Line Debouncing
Period

lineDebouncingPeriod

Specifies the minimum delay before an input line
voltage transition is recognizing as a signal
transition.

1.00
DFNC
Beginner

«
...
59
60
61
62
63
...
»

Содержание Linea ML ML-FM-08K30H




















































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды