Dali Wireless airHost PS Скачать руководство пользователя страница 97

Страница: 97 / 243

Matrix PS System Installation and Commissioning Guide

Dali Wireless Proprietary and Confidential | DW-MAN-036 Rev 06

9.3.2

Daisy Chain Configuration

In a daisy-chain configuration, the first remote in the chain is connected to the host. The

first remote connects to a second remote, and the second to a third, and so on.

When remotes are daisy-chained, the failure of one remote in the chain can cause the

downstream remotes to lose signal. A Dali optical bypass switch ensures the continuity

of signal flow by rerouting the signal from the failed unit to the next remote in the chain.

Contact Dali Customer Service about installation and configuration of this option.

The number of daisy-chained remotes depends on maximum round trip delay between

the host and the furthest remote. For example, an office building with a dedicated base

station could support 20 or more daisy-chained remotes.

Figure 9-2: Remotes Connected in Daisy-Chain Configuration

Host units can also be daisy chained, for more optical port capacity.

Figure 9-3: Hosts Connected in Daisy-Chain Configuration

Содержание airHost PS




















































































































































































































































Результаты поиска

Содержание airHost PS

Отзывы:

Похожие инструкции для airHost PS

Бренды по названию

Популярные бренды

Dali Wireless airHost PS, Инструкция по установке и наладке

Результаты поиска

Содержание airHost PS

Отзывы:

Похожие инструкции для airHost PS

Бренды по названию

Популярные бренды