Daktronics ST-3170 Скачать руководство пользователя страница 3

Страница: 3 / 50

– i –

Table of Contents

Important Safeguards ..........................................................................................................................1

Specifications

........................................................................................................................................1

Resources ..............................................................................................................................................2
Daktronics Nomenclature ...................................................................................................................2
Light Strip Controllers ............................................................................................................................3

2 Uncrating ��4

Attach Caster Bases .............................................................................................................................4
Remove Table from Shipping Brackets ..............................................................................................7

3 Mechanical Installation ��9

4 Electrical Installation ��22

5 Maintenance & Troubleshooting ��25

Recommended Tools .........................................................................................................................26
Component Location & Access .......................................................................................................26

Front Access��26
Rear Access ��27

Replacing an LED Edge Light Strip ...................................................................................................27
Replacing a Power Supply ................................................................................................................28
Light Strip Driver ...................................................................................................................................28

Replacing a Driver ��29
Setting the Driver Address ��30

Tabletop Possession Indicators ..........................................................................................................30

6 Daktronics Exchange and Repair & Return Programs ��31

Exchange Program ............................................................................................................................31
Repair & Return Program ...................................................................................................................32
Daktronics Warranty & Limitation of Liability ...................................................................................32

A Reference Drawings ��33
B Daktronics Warranty and Limitation of Liability ��41

Содержание ST-3170



















































Результаты поиска

Содержание ST-3170

Отзывы:

Daktronics ST-3170, Руководство пользователя, Страница: 3 / 50

Результаты поиска

Содержание ST-3170

Отзывы: