Daktronics ST-3170 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 50

Daktronics ST-3170 Скачать руководство пользователя страница 26

Electrical Installation

22

4 Electrical Installation

This scorers table system is intended to be installed in accordance with the requirements

of Article 600 of the National Electrical Code and/or other applicable local codes.

This includes proper grounding and bonding of the sign. This display is suitable for dry

locations only. Only qualified individuals should terminate power and signal cable and

access the electrical components of this display and its associated equipment.

Warnings and Disclaimers

• Ensure that all electrical work meets or exceeds all local or national electrical codes.
• Provide the required power to the display as listed on the product labels,

specifications, or site-specific riser drawings. The conductor size may vary based on

the length of the power run.

• Consider implementing a separate circuit for the display using an isolation

transformer or dedicated transformer.

•

Daktronics assumes no liability for any issues caused by line voltage fluctuations or

other improper power conditions.

Power Connection

The power cable is available in 25' (7.6 m), 50' (15.2 m), or 75' (22.9 m)

lengths. Use a T25 Torx bit to remove the screws securing the lower-

right access panel under the tabletop. Connect one end of the

power cable to the

120V AC IN

jack and the other end to a standard

15 Amp receptacle in the wall/floor box. Refer to

.

Convenience & USB Outlets

Scorers tables are equipped with 4 or 8 convenience outlets, depending on the table’s

width, for plugging in control equipment and other small electronic devices. A 10 Amp

resettable breaker limits the total convenience outlet power draw. Tables also feature

8 USB outlets (2 outlets with 4 ports each) to power cellphones, tablets, and other

equipment with USB chargers.
Refer to the Mechanical Specs drawing in

Appendix A

for outlet and breaker locations.

Figure 39:

Power IN

«
...
24
25
26
27
28
...
»

Содержание ST-3170



















































Отзывы:

Нет отзывов