manualshive.com logo in svg

Daktronics ST-3170, Руководство пользователя, Страница: 13 / 50

Поделиться
Скачать
Daktronics ST-3170 Скачать руководство пользователя страница 13

Mechanical Installation

9

3  Mechanical Installation

All decisions regarding display setup must conform to the specifications and guidelines 

in this section. Read both the mechanical and electrical installation sections before 

beginning any installation procedures. 

Reference Drawings:

Mechanical Spec; ST-3170 ..............................................................................

DWG-4909964

The tabletop should be upright only during games and events, and it should be in the 

dropped position when moving and storing the table. The tabletop capacity is rated at a 

maximum of 150 lb (68 kg). 
Depending on the length of the power cords, the table(s) should be within 25' (7.6 m), 50' 

(15.2 m), or 75' (22.9 m) of a power outlet. 

Caster Base Tool

Each table comes with one Caster Base Tool (Daktronics part # HS-4939703) located in 

the bottom channel of each caster base (two per table). Refer to 

Figure 16

. These tools 

serve a dual purpose of helping to pull down the caster base pivot arms when setting up 

the table as well as setting the display face to the desired angle. The tools are attached 

to the caster base by a steel lanyard to prevent being lost or stolen. 

Figure 16: 

Caster Base Tool

Содержание ST-3170



















































Отзывы:

Нет отзывов