manualshive.com logo in svg

Daktronics ST-3170, Руководство пользователя, Страница: 31 / 50

Поделиться
Скачать
Daktronics ST-3170 Скачать руководство пользователя страница 31

Maintenance & Troubleshooting

27

Rear Access

1� 

Disconnect the power to the display. 

2� 

Lift the tabletop upward and secure in place as described in 

Table Setup – Transport 

to Stationary Mode (p�10)

. 

3� 

Use a T25 Torx bit to remove the two screws securing the appropriate access door. 

4� 

Carefully allow the access door to lower downward into the open position. 

Replacing an LED Edge Light Strip

1� 

Access the table from the front as described in 

Front Access (p�26)

. 

2� 

For easier access to the LED edge light strip, it may be necessary to remove all T25 

Torx screws along the top retainer as shown in 

Figure 46

. 

3� 

Use a 3/8" nut driver to remove the nuts securing the LED edge light strip to the top 

retainer. Refer to 

Figure 47

. 

Figure 47: 

LED Edge Light Strip (as Viewed with Side Pads Removed)

4� 

Remove the malfunctioning edge light strip by disconnecting the mini Mate-N-Lok 

connectors from the adjacent light strip(s). 

5� 

Connect the new edge light strip to the rest of the string using the mini Mate-N-Lok 

connectors and use a 3/8" nut driver to replace the nuts.

6� 

Replace the top retainer, face panel, and top plex retainer, then power up and test 

the display to verify the issue has been resolved.

Содержание ST-3170



















































Отзывы:

Нет отзывов