Daktronics ST-3170 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 50

Daktronics ST-3170 Скачать руководство пользователя страница 34

Maintenance & Troubleshooting

30

6�

Reconnect all plugs to the driver. These are keyed connectors and will attach in one

way only. Do not force the connections.

7�

Ensure the new driver is set to the correct address. This will be the same address as

the old driver being replaced. Refer to

Setting the Driver Address (p�30)

.

8�

Close and secure the access panel, then power up and test the display to verify the

issue has been resolved.

Setting the Driver Address

For the light strip driver to receive signal and function properly, the driver must be set to

the correct address.

Optional light strip drivers use Address 1�

This address is set with jumper wires in a 12-pin plug which mates with jack

J19

, located

in the upper-right corner of the driver as shown in

. It may be possible to reuse

the same address plug from the driver that was replaced. If not, order an

Address 1

plug

(part # 0A-1150-0122).

Tabletop Possession Indicators

To replace an optional tabletop possession indicator arrow/colon:

1�

Unplug the possession indicator from the designated convenience outlet.

2�

Remove the screws securing the possession indicator cover.

3�

Disconnect the power/signal cable from the malfunctioning indicator.

4�

Use a 11/32" nut driver to remove the nuts securing the indicator, and then lift it off

the stud inserts.

5�

Position a new indicator over the studs (making sure the small plastic spacers are still

in place), and then tighten the nuts.

6�

Reconnect the power/signal cable, and replace all screws for the indicator cover.

7�

Plug the possession indicator back into the designated convenience outlet, then

power up and test the display to verify the issue has been resolved.

«
...
32
33
34
35
36
...
»

Содержание ST-3170



















































Отзывы:

Нет отзывов