Daktronics ST-3170 Скачать руководство пользователя страница 44

Страница: 44 / 50

THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING

ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY

ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF

DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES.

THIRD ANGLE PROJECTION

REV

TITLE:

PROJECT:

INCHES [MILLIMETERS]

DESIGN:

SCALE:

DIM UNITS:

DATE:

SHEET

DO NOT SCALE DRAWING

FUNC - TYPE - SIZE

DRAWN:

JOB NO.

ST-3170 TABLES

MECHANICAL SPEC; ST-3170

MCARSRU

29 JUL 21

P2307

E 10 B

1/45

MCARSRU

4909964

3'-0"

OVERALL HEIGHT

CHANGES W/

FACE ANGLE

2'-5 1/8"

COUNTER HEIGHT

CHANGES W/

FACE ANGLE

2'-5 3/4"

2'-8 3/8"

OVERALL DEPTH

CHANGES W/ FACE ANGLE

FRONT VIEW

6-WIDE COURTSIDE TABLE

12-WIDE COURTSIDE TABLE

REAR VIEW

6-WIDE COURTSIDE TABLE

12-WIDE COURTSIDE TABLE

3'-0"

OVERALL

HEIGHT

0'-2 1/2"

4'-11"

9'-10 1/8"

0'-2 1/2"

RIGHT SIDE

STATIONARY MODE

TRANSPORT MODE

3'-5 3/8"

2'-4 3/4"

5°

FACE ANGLE

ADJUSTABLE

FROM 0°-15°

ROTATED FRONT VIEW

ROTATED REAR VIEW

2'-0"

0'-4 1/2"

0'-11 1/2"

0'-1 7/8"

0'-6 1/4"

RIGHT SIDE

STATIONARY MODE

(SHOWN W/O END PADS)

LEFT SIDE

STATIONARY MODE

(SHOWN W/END PADS)

LEFT SIDE

STATIONARY MODE

(SHOWN W/O END PADS)

DETAIL A

SCALE 1:6

0'-3 5/8"

0'-2 7/8"

TOP PAD HINGES

FORWARD FOR

CABLE TRAY

ACCESS

CABLE TRAY

AREA

ACCESSORY USB OUTLETS

(LOCATED ON BACKSPLASH)

@2 ON ALL TABLES

DAK NETWORK

JACK LOCATIONS

ACCESSORY OUTLETS/

CUSTOMER NETWORK JACKS

(LOCATED ON BACKSPLASH) @4

ACCESSORY OUTLETS/

CUSTOMER NETWORK JACKS

(LOCATED ON BACKSPLASH) @10

0'-5 7/8"

TYP. EACH END

AND ALL TABLES

1'-1 3/4"

TYP. EACH END

AND ALL TABLES

SIGNAL IN

POWER IN

SIGNAL IN

POWER IN

SIGNAL OUT

0'-7"

OPTIONAL LED LIGHT STRIP

LOCATED BELOW MODS/

BEHIND PROTECTIVE POLYCARBONATE

PROTECTIVE POLYCARBONATE

12-WIDE SPONSOR

COPY AREA: 2'-4 1/4"X9'-10 1/8"

WEIGHT: 260 LBS

6-WIDE SPONSOR

COPY AREA: 2'-4 1/4"X4'-11"

WEIGHT: 160 LBS

Содержание ST-3170



















































Результаты поиска

Содержание ST-3170

Отзывы:

Daktronics ST-3170, Руководство пользователя, Страница: 44 / 50

Результаты поиска

Содержание ST-3170

Отзывы: