Daktronics ST-3170 Скачать руководство пользователя страница 43

Страница: 43 / 50

THE CONCEPTS EXPRESSED AND DETAILS SHOWN ON THIS DRAWING

ARE CONFIDENTIAL AND PROPRIETARY. DO NOT REPRODUCE BY

ANY MEANS WITHOUT THE EXPRESS WRITTEN CONSENT OF

DAKTRONICS, INC. OR ITS WHOLLY OWNED SUBSIDIARIES.

THIRD ANGLE PROJECTION

REV

TITLE:

PROJECT:

INCHES [MILLIMETERS]

DESIGN:

SCALE:

DIM UNITS:

DATE:

SHEET

DO NOT SCALE DRAWING

FUNC - TYPE - SIZE

DRAWN:

JOB NO.

ST-31XY

LIGHT STRIP ATTACHMENT

JFIXSEN

23 JUN 21

P2307

R 01 B

NTS

JFIXSEN

4889870

P2307_LIGHT_STRIP_ATT

INDE

NAME

DESCRIPTION

DS-4263053

GEN 2, STRIP LIGHTING, LED, BLAXE X, 18", RED, 24V, IN

ONLY

HC-1302

TAP SCR, #6-20 X 0.750, PHIL FLAT HEADM BLK

HS-3763489

CHROMAPATH SLIM BLACK U-CLIP PAIR

OPTIONAL ATTACH CLOCK STOP

LIGHT STRIP WITH CLIPS AND

MOUNTING SCREWS REFER

TO DETAIL A

DETAIL A

ATTACH CLIPS AND

LIGHT STRIPS PER

DETAIL A.

REMOVE KNOCKOUTS AT MIDDLE OF TABLE

TO ALLOW FOR LIGHT STRIP TO HOOK

TOGETHER. KNOCKOUTS MUST BE REMOVED

AT EACH END OF THE LIGHT STRIPS.

FRONT VIEW

REAR VIEW

LIGHT STRIP

DRIVER TRAY

LIGHT STRIP CNTRL

MOUNT TO TABLE USING

HC-1554 @4 AND HC-1243 @4

(5 IN-LBS)

FRONT VIEW

MALE CONNECTOR

REV

DATE:

BY:

AUG 30 21

JSF

CN126606 ADDED NOTE FOR WHICH SIDE OF LIGHT STRIP

HAS MALE AND FEMALE ENDS

MALE CONNECTOR

REV

DATE:

BY:

28 JAN 22

JSF

CN-133848 UPDATED LIGHT STRIP MOUNTING

SCREW

PPaarrtt ## -- D

G--0044888899887700

VVeerrssiioonn -- 0022..22

Deessccrriippttiioonn -- N

N BB LLIIG

HTT SSTTR

RIIPP AATTTTAAC

MEEN

NTT

LLiiffeeccyyccllee SSttaattee -- FFuullll PPrroodduuccttiioonn

LLaasstt M

Mooddiiffiieedd BByy -- jjffiixxsseenn

LLaasstt M

Mooddiiffiieedd -- 22002222--0011--2288

Содержание ST-3170



















































Результаты поиска

Содержание ST-3170

Отзывы:

Daktronics ST-3170, Руководство пользователя, Страница: 43 / 50

Результаты поиска

Содержание ST-3170

Отзывы: