manualshive.com logo in svg

Daktronics ST-3170, Руководство пользователя, Страница: 28 / 50

Поделиться
Скачать
Daktronics ST-3170 Скачать руководство пользователя страница 28

Electrical Installation

24

Possession Indicator

Daktronics scorers tables may have an optional possession indicator that sits atop the 

table padding. Refer to 

Figure 43

. Possession indicators are designed so they can be 

positioned anywhere along the length of the top pad to best align with the center of a 

single table or a row of tables. 
Possession indicators mount to the top pad by sliding on from the rear and then using a 

#2 Phillips screwdriver or 5/16" socket to tighten the set screws on the bottom flange. Plug 

the power cord into the dedicated convenience outlet labeled 

POSS� INDICATOR OUTLET 

ONLY

. Refer to 

Figure 44

. To operate, simply flip the switch on the back of the unit toward 

the side of the court that has possession, and the LED indicators will illuminate on both 

the front and back of the unit. 

Set Screws

Figure 43: 

Possession Indicator, Rear View

Figure 44: 

Possession Indicator 

Outlet ONLY

Содержание ST-3170



















































Отзывы:

Нет отзывов