manualshive.com logo in svg

DaimlerChrysler Jeep Grand Cherokee 2002, Руководство по обслуживанию

Поделиться
Скачать
DaimlerChrysler Jeep Grand Cherokee 2002 Скачать руководство пользователя страница 97

Symptom:

P0403-EGR SOLENOID CIRCUIT OPEN CIRCUIT

When Monitored and Set Condition:

P0403-EGR SOLENOID CIRCUIT OPEN CIRCUIT

When Monitored:

With the ignition on.

Set Condition:

The ECM detects an open or short to ground on the EGR Solenoid Control

circuit.

POSSIBLE CAUSES

INTERMITTENT CONDITION

ASD RELAY OUTPUT CIRCUIT OPEN

EGR SOLENOID CONTROL CIRCUIT SHORTED TO GROUND

EGR SOLENOID CONTROL CIRCUIT OPEN

SUBSTITUTE EGR SOLENOID

ENGINE CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Turn the ignition on.
With the DRB, erase ECM DTCs.
Perform several ignition cycles, turning the ignition off for at least 10 seconds
between each ignition cycle.
Monitor the DRB for ECM DTCs.
Did this DTC set again?

All

Yes

→

Go To

2

No

→

Go To

7

2

Turn the ignition off.
Disconnect the EGR Solenoid harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the ASD Relay Output circuit.
Does the test light illuminate brightly?

All

Yes

→

Go To

3

No

→

Repair the ASD Relay Output circuit for an open.
Perform ROAD TEST VERIFICATION - VER-2.

3

Turn the ignition off.
Disconnect the EGR Solenoid harness connector.
Disconnect the ECM harness connectors.
Measure the resistance between ground and the EGR Solenoid Control circuit.
Is the resistance above 100 kohms?

All

Yes

→

Go To

4

No

→

Repair the EGR Solenoid Control circuit for a short to ground.
Perform ROAD TEST VERIFICATION - VER-2.

89

DRIVEABILITY - DIESEL

ProCarManuals.com

Содержание Jeep Grand Cherokee 2002





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды